Welcome! Log In Create A New Profile

Advanced

Fisher

... it's a small Delta printer from RepRapPro 
Subject Views Posts Last Post

new effector and carraige   (Pages: 1 2)

by bgkdavis
1,241 48 04/07/2016 02:07PM
Last Post by geeksarebeta

Lighting setups

by ByteSlinger
307 6 04/07/2016 04:28AM
Last Post by SSMagic

Lost network connection mid-print

by ByteSlinger
251 4 04/06/2016 12:58PM
Last Post by dc42

Maintenance?

by Theolodian
670 10 04/04/2016 09:12AM
Last Post by SSMagic

Extruder temperature after adding heated bed.

by DADIY
296 5 03/31/2016 12:21PM
Last Post by DADIY

Carbon Arms (Again) Attachments   (Pages: 1 2)

by lord_alan
1,551 32 03/30/2016 05:52AM
Last Post by Sean.kennedy

Prints warping

by pixelseventy2
368 5 03/27/2016 02:57PM
Last Post by Wissing

About USB connection

by tavietbao
334 8 03/22/2016 03:25AM
Last Post by tavietbao

Thermistor value for heated bed.

by seatroutfisher
549 19 03/21/2016 05:33PM
Last Post by dc42

Newbie need help

by tavietbao
408 21 03/21/2016 03:43AM
Last Post by dc42

Problem using temperature over 220C

by glompos21
297 3 03/20/2016 12:53PM
Last Post by glompos21

Extruder motor struggles past nozzel

by ByteSlinger
633 22 03/20/2016 08:13AM
Last Post by ByteSlinger

My Fisher experience (so far..) and advice for anyone about to build one Attachments

by Geoffro
1,025 8 03/16/2016 10:50AM
Last Post by janpenguin

How to insert new roll of filament while in printing?

by janpenguin
294 2 03/12/2016 02:20AM
Last Post by bgkdavis

Octoprint?

by upsch2000
347 2 03/11/2016 04:36PM
Last Post by dc42

Needing spare parts (printed)

by FragrantParrot
252 3 03/10/2016 07:36PM
Last Post by FragrantParrot

Fisher Minimum Wall Thickness

by geeksarebeta
261 3 03/07/2016 04:03AM
Last Post by geeksarebeta

Panel designs optimized for metal Attachments

by StupendousMan
403 13 03/03/2016 05:11AM
Last Post by StupendousMan

U.S. Fisher distributor?

by BioLumo
268 2 02/28/2016 07:57AM
Last Post by StupendousMan

Bushing Instead of Bearings?

by DADIY
289 2 02/24/2016 10:48AM
Last Post by StupendousMan

Hot End Blocked?

by geeksarebeta
288 3 02/14/2016 03:41PM
Last Post by PRZ

Mistacke with Duet Web Control 1.08 and RepRapFirmware 1.09r-ch

by Anubis_Juventino
332 5 02/13/2016 05:07AM
Last Post by Anubis_Juventino

Dead fan?

by ntsewell
270 7 02/10/2016 12:16PM
Last Post by DADIY

Hot end not cooling enough?

by ByteSlinger
263 3 02/08/2016 10:45AM
Last Post by Martoh

Looking to build up a kit of spares...

by lord_alan
314 3 02/08/2016 07:37AM
Last Post by StupendousMan

Config.g for Firmware 1.09r

by ByteSlinger
311 3 02/07/2016 06:34PM
Last Post by ByteSlinger

Fisher printing of 3DBenchy Attachments

by tblitzy
944 20 02/01/2016 10:48AM
Last Post by JamesK

Meet the Fisher XT Attachments

by DADIY
606 11 02/01/2016 03:58AM
Last Post by DADIY

Idler Lever not holding tension

by ByteSlinger
256 3 01/31/2016 09:31PM
Last Post by PRZ

RepRapPro closed down, but need a rod

by ronnietucker
575 11 01/29/2016 07:35AM
Last Post by jmgiacalone