Welcome! Log In Create A New Profile

Fisher

... it's a small Delta printer from RepRapPro

Page 4 of 10 Pages:

1 2 345

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	My Fisher experience (so far..) and advice for anyone about to build one by Geoffro	1,785	8	03/16/2016 10:50AM Last Post by janpenguin
	How to insert new roll of filament while in printing? by janpenguin	938	2	03/12/2016 02:20AM Last Post by bgkdavis
	Octoprint? by upsch2000	1,012	2	03/11/2016 04:36PM Last Post by dc42
	Needing spare parts (printed) by FragrantParrot	932	3	03/10/2016 07:36PM Last Post by FragrantParrot
	Fisher Minimum Wall Thickness by geeksarebeta	1,003	3	03/07/2016 04:03AM Last Post by geeksarebeta
	Panel designs optimized for metal by StupendousMan	1,149	13	03/03/2016 05:11AM Last Post by StupendousMan
	U.S. Fisher distributor? by BioLumo	1,049	2	02/28/2016 07:57AM Last Post by StupendousMan
	Bushing Instead of Bearings? by DADIY	1,088	2	02/24/2016 10:48AM Last Post by StupendousMan
	Hot End Blocked? by geeksarebeta	1,075	3	02/14/2016 03:41PM Last Post by PRZ
	Mistacke with Duet Web Control 1.08 and RepRapFirmware 1.09r-ch by Anubis_Juventino	1,046	5	02/13/2016 05:07AM Last Post by Anubis_Juventino
	Dead fan? by ntsewell	1,019	7	02/10/2016 12:16PM Last Post by DADIY
	Hot end not cooling enough? by ByteSlinger	1,056	3	02/08/2016 10:45AM Last Post by Martoh
	Looking to build up a kit of spares... by lord_alan	1,036	3	02/08/2016 07:37AM Last Post by StupendousMan
	Config.g for Firmware 1.09r by ByteSlinger	1,100	3	02/07/2016 06:34PM Last Post by ByteSlinger
	Fisher printing of 3DBenchy by tblitzy	2,079	20	02/01/2016 10:48AM Last Post by JamesK
	Meet the Fisher XT by DADIY	1,539	11	02/01/2016 03:58AM Last Post by DADIY
	Idler Lever not holding tension by ByteSlinger	986	3	01/31/2016 09:31PM Last Post by PRZ
	RepRapPro closed down, but need a rod by ronnietucker	1,376	11	01/29/2016 07:35AM Last Post by jmgiacalone
	Wood and Bronze Filament by ByteSlinger	1,093	6	01/29/2016 03:30AM Last Post by DADIY
	problem with fisher 1 by Anubis_Juventino	1,053	4	01/26/2016 06:32PM Last Post by bgkdavis
	Logo STL by ByteSlinger	1,217	3	01/23/2016 08:50AM Last Post by reprapprochina
	Carbon Arms (Pages: 1 2) by bgkdavis	3,585	36	01/21/2016 07:04PM Last Post by bgkdavis
	Homing finishes 14mm above print bed... by ByteSlinger	1,099	1	01/20/2016 06:31PM Last Post by ByteSlinger
	Can I make a Fisher without reprappro parts? by StupendousMan	1,291	6	01/18/2016 09:43PM Last Post by bgkdavis
	Simplify3D setup? (Pages: 1 2) by Theolodian	5,382	57	01/18/2016 04:48PM Last Post by jmg123
	Hot end peaks at 145 then drops back down by ByteSlinger	960	2	01/18/2016 04:28PM Last Post by dc42
	Spare parts by Thorn666	1,187	14	01/18/2016 08:51AM Last Post by DADIY
	Getting low resistance on pre-powerup check by ByteSlinger	1,044	1	01/17/2016 06:52PM Last Post by ByteSlinger
	Calibration Speed. by DADIY	1,115	5	01/17/2016 12:10PM Last Post by DADIY
	Fisher Rod DXF download - [FOUND] by ByteSlinger	1,090	3	01/13/2016 09:43PM Last Post by PRZ

Page 4 of 10 Pages:

1 2 345