Welcome! Log In Create A New Profile


Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Subject Views Posts Last Post

Upgrading from V1.1 to V2.0 benefits

by iamturbo1978
402 3 04/11/2018 04:48PM
Last Post by MMcLure

Momentary Grinding Noise

by lamina
156 3 04/10/2018 09:51AM
Last Post by lamina

Atmega2560 Internal Voltmeter

by platitude
190 2 04/09/2018 11:43AM
Last Post by JustSumGuy

error deactivate motor prusa i3

by giuseppe_reprap
169 1 04/08/2018 10:27AM
Last Post by giuseppe_reprap

Z axis Homing Issue

by Brass-51
1,158 12 04/07/2018 01:45AM
Last Post by ZPRO Solutions

Heated Bed Not Showing up on LCD

by icecats
141 4 04/07/2018 01:35AM
Last Post by Dust

Info about real Manual Bed Leveling

by brunosso
329 10 04/06/2018 11:58AM
Last Post by brunosso

marlin for anet A6 +bltouch

by xavier59165
564 1 03/26/2018 10:51PM
Last Post by xavier59165

Need Help With BL Touch

by 3DNublet
500 3 03/26/2018 10:40PM
Last Post by xavier59165

No Babystep Z axis with BLTouch?

by 3DStyle
227 4 03/26/2018 10:35AM
Last Post by Roxy

Adding menu for Laser cut calibration

by pirlouwi
163 2 03/24/2018 07:09PM
Last Post by pirlouwi

Temps reading high, using AD595 with Thermocouples Attachments

by ricknsharon
146 4 03/22/2018 08:45PM
Last Post by Roberts_Clif

Only some endstops function Attachments

by ricknsharon
149 3 03/22/2018 12:09PM
Last Post by ricknsharon

PID Weirdness Attachments

by DaHai8
226 4 03/22/2018 03:00AM
Last Post by DaHai8

Homing offsets

by MarinusK
174 1 03/21/2018 06:09AM
Last Post by MarinusK

Z_Probe working strategy

by Mohan Muthusamy
243 3 03/20/2018 10:14AM
Last Post by Roxy

Is M915 / TMC_Z_CALIBRATION with TMC 2130 useful?

by tbeaulieu
193 2 03/20/2018 10:11AM
Last Post by Roxy

Cooling the bed at the end of a print automatically.

by isolt
136 1 03/19/2018 08:56PM
Last Post by isolt

Marlin 1.1.8 and my CR10s It aint liking it!

by cyborblades
1,029 6 03/19/2018 12:07PM
Last Post by cyborblades

Auto calibration points

by robingantois
174 1 03/18/2018 11:38AM
Last Post by robingantois

Problem with LCD on Mini-Rambo Attachments

by dpalo
134 2 03/18/2018 11:06AM
Last Post by obewan

Mightyboard 2004 LCD with Marlin?

by villamany
341 2 03/16/2018 08:29AM
Last Post by Dust

Octoprint & EEPROM CRC checksum Errors

by sinned
451 2 03/15/2018 11:26PM
Last Post by Roxy

Need Help Configuring EndStops

by 3DNublet
418 14 03/15/2018 11:19AM
Last Post by 3DNublet

Calibrating steps per mm/in on A,B,C steppers on a delta

by jemenake
119 3 03/15/2018 12:02AM
Last Post by jemenake

Possible to Change Message "E1 heating..."?

by 3DStyle
195 2 03/12/2018 05:24PM
Last Post by 3DStyle

Possible to Change Message "E1 heating..."?

by 3DStyle
153 1 03/12/2018 05:23PM
Last Post by 3DStyle

Marlin 2.0 and Smoothie

by StlLooking
907 4 03/12/2018 02:04PM
Last Post by Techgirl

[1.1.8] G26 Pattern didn't finish and then lowerd the Z axis

by Gazit6
123 2 03/11/2018 07:48PM
Last Post by Roxy

Does marlin BEEP when 3d print is done ?

by windchime
198 6 03/09/2018 01:21AM
Last Post by Melty