Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Page 2 of 21    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Ethernet troubles with 0.6 and firmware 1.20

by maso 		182 4 02/27/2018 03:56PM
Last Post by dc42

bed dimension calibration.

by JustSumGuy 		174 3 02/26/2018 02:39PM
Last Post by JustSumGuy

SD Card Structure 3DP Micro Attachments

by Bill Clark 		191 1 02/25/2018 09:31PM
Last Post by Bill Clark

Strange steps per mm to rounds per minute conversion

by DrPFF 		189 12 02/25/2018 03:58AM
Last Post by o_lampe

Duet Ethernet - Dual Extruders - Macros/Switching Extruders

by blandified 		209 13 02/24/2018 05:38PM
Last Post by dc42

Controlling two DuetWifi ?

by o_lampe 		197 7 02/21/2018 04:07AM
Last Post by dc42

connecting to wifi problem Attachments

by JustSumGuy 		169 4 02/19/2018 12:57PM
Last Post by JustSumGuy

5v inductive sensor to Duet Wifi

by JustSumGuy 		446 7 02/13/2018 01:11PM
Last Post by JustSumGuy

Problem with BLTouch after upgrading to Firmware 1.20

by drmaestro 		258 2 02/10/2018 04:03PM
Last Post by dc42

DUET 0.6 heat bed power not working Attachments

by selva_tvi 		178 4 02/08/2018 11:38AM
Last Post by JustSumGuy

DuetWifi Paneldue Heater Issue Attachments

by gadittri 		249 6 02/03/2018 03:45PM
Last Post by dc42

Duet WiFi temperatures are too low.

by Treito 		297 5 01/28/2018 08:58AM
Last Post by dc42

basic protocol for using baby-stepping?

by shadowphile 		176 3 01/28/2018 05:19AM
Last Post by shadowphile

print froze halfway up

by shadowphile 		145 7 01/28/2018 03:18AM
Last Post by dc42

Duet WiFi - problems with interpolation.

by Treito 		289 1 01/21/2018 05:51AM
Last Post by Treito

firmware upgrade latest version

by JustSumGuy 		332 5 01/10/2018 04:49PM
Last Post by JustSumGuy

G31 probe offset confusion

by o_lampe 		332 3 01/03/2018 11:56AM
Last Post by o_lampe

"Attempting to extrude with no tool selected", and how to set up fans

by Lobotomy 		303 8 01/03/2018 03:44AM
Last Post by o_lampe

My proximity sensor endstops not working Attachments

by chichirod 		286 7 12/31/2017 01:27PM
Last Post by dc42

Duet 0.6 Bed temperature is too low.

by Treito 		218 10 12/29/2017 05:10AM
Last Post by Treito

Cannot invert Z probe value

by Tennysballs 		259 4 12/23/2017 10:08AM
Last Post by Tennysballs

Crunchy X-axis on Duet Wifi

by cheeseandham 		293 4 12/22/2017 05:34PM
Last Post by dc42

controlled heated box

by JustSumGuy 		311 7 12/20/2017 04:35PM
Last Post by JustSumGuy

BLT and DeutWiFi not working as intended.

by Dunston-UK 		329 11 12/20/2017 07:09AM
Last Post by Dunston-UK

Repair a Duet 0.85 a "little bit" hot ?

by Crixos 		224 6 12/19/2017 09:06AM
Last Post by dc42

My endstops do not work? (RADDS + Kossel Delta) Attachments

by Lobotomy 		302 7 12/19/2017 03:19AM
Last Post by o_lampe

RepRapFirmware 1.20 RC2 now available

by dc42 		301 2 12/14/2017 11:31AM
Last Post by JustSumGuy

Extruder skipping steps?confused smiley

by Kevin37 		527 26 12/12/2017 10:23AM
Last Post by Kevin37

Bed Mesh

by jbolt 		231 4 12/12/2017 03:12AM
Last Post by o_lampe

Turning OFF & ON the DuetWiFi with a relay Attachments

by Dunston-UK 		272 3 12/08/2017 01:56PM
Last Post by Dunston-UK
Page 2 of 21    Pages: Previous12345NextLast