Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post

Please help: Ormerod 1 its been a while!! What do I need.

by gregstah
438 7 06/29/2017 09:06AM
Last Post by Karoo Klong

Duetwifi and Diamond hotend on Delta

by hvashist
384 2 06/28/2017 03:08AM
Last Post by o_lampe

M584 driver mapping ignores different steps/mm

by o_lampe
291 3 06/23/2017 09:52AM
Last Post by o_lampe

Hot End Heating Up When Power Turned On Attachments

by Kurzaa
713 6 06/22/2017 02:41AM
Last Post by dc42

Which IP Cam?

by DeltaCon
347 2 06/20/2017 06:27PM
Last Post by dc42

Fan voltage

by fma
650 5 06/20/2017 06:20AM
Last Post by fma

Support for mixing extruders

by fma
312 2 06/20/2017 05:48AM
Last Post by dc42

Intermittend stepper hickup after cold start

by o_lampe
317 3 06/14/2017 01:34AM
Last Post by o_lampe

Doing action when changing status

by maczar
284 2 06/13/2017 02:14AM
Last Post by dc42

Hot end crashes into second layer

by alangibson
460 6 06/12/2017 09:43AM
Last Post by DeltaCon

(ignore) PC not connecting to new Duet-Ethernet board (windows)

by shadowphile
651 1 06/11/2017 06:33PM
Last Post by shadowphile

4 axis polar geometry

by fma
322 8 06/09/2017 02:29PM
Last Post by fma

Web interface

by fma
336 3 06/09/2017 08:01AM
Last Post by fma

Mixing cartesian and CoreXY config?

by o_lampe
493 14 06/08/2017 07:39AM
Last Post by dc42

Connecting your Duet 0.85 Straight to Computers Ethernet

by chris33
441 2 06/07/2017 05:37PM
Last Post by dc42

RepRapFirmware 1.18 and Panel Due firmware 1.16 released   (Pages: 1 2)

by dc42
1,539 34 06/06/2017 05:09PM
Last Post by dc42

Extruder motor going both forward and backwards on extrude

by ElmoC
669 5 06/04/2017 08:39AM
Last Post by ElmoC

Storing Calibration?

by clearlynotstefan
401 2 06/03/2017 03:50AM
Last Post by dc42

Firmware 1.18.1 and Heater Faults

by DRTak
1,682 12 06/02/2017 01:23PM
Last Post by dc42
This topic has been moved.

Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC

by Italia
    This topic has been moved.

Duet Wifi, two drivers for one 8 wire motor?

by M;kko
338 2 05/29/2017 02:20AM
Last Post by dc42

Mechanical switch for z probe

by chris33
781 10 05/25/2017 05:19PM
Last Post by chris33

M997 S2

by 3D-Print
382 2 05/24/2017 02:26AM
Last Post by dc42

M572 pressure advance for Diamond hotend?

by o_lampe
389 5 05/23/2017 06:17AM
Last Post by dc42

Fan selection?

by clearlynotstefan
763 4 05/23/2017 02:18AM
Last Post by drmaestro

PanelDue STOP not the same as DWC Emergency Stop?

by PDBeal
328 3 05/22/2017 04:12PM
Last Post by dc42

Firmware upgrade

by joestefano
480 9 05/17/2017 04:18AM
Last Post by dougal1957

Fan short!

by clearlynotstefan
340 6 05/14/2017 01:33AM
Last Post by clearlynotstefan

Raspberry Pi as display

by Napalm1432
655 7 05/12/2017 02:26AM
Last Post by o_lampe

just a quick connector question

by chris33
345 3 05/07/2017 04:21PM
Last Post by dc42