Welcome! Log In Create A New Profile

Duet

Duet is the Arduino Due Compatible RepRap Electronics

Page 9 of 25 Pages:

7 8910 11

Forum List New Topic RSS

	Views	Posts	Last Post
Extruder motor going both forward and backwards on extrude by ElmoC	1,365	5	06/04/2017 08:39AM Last Post by ElmoC
Storing Calibration? by clearlynotstefan	635	2	06/03/2017 03:50AM Last Post by dc42
Firmware 1.18.1 and Heater Faults by DRTak	4,705	12	06/02/2017 01:23PM Last Post by dc42
Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC by Italia			This topic has been moved.
Duet Wifi, two drivers for one 8 wire motor? by M;kko	509	2	05/29/2017 02:20AM Last Post by dc42
Mechanical switch for z probe by chris33	1,312	10	05/25/2017 05:19PM Last Post by chris33
M997 S2 by 3D-Print	692	2	05/24/2017 02:26AM Last Post by dc42
M572 pressure advance for Diamond hotend? by o_lampe	642	5	05/23/2017 06:17AM Last Post by dc42
Fan selection? by clearlynotstefan	1,156	4	05/23/2017 02:18AM Last Post by drmaestro
PanelDue STOP not the same as DWC Emergency Stop? by PDBeal	545	3	05/22/2017 04:12PM Last Post by dc42
Firmware upgrade by joestefano	692	9	05/17/2017 04:18AM Last Post by dougal1957
Fan short! by clearlynotstefan	533	6	05/14/2017 01:33AM Last Post by clearlynotstefan
Raspberry Pi as display by Napalm1432	1,182	7	05/12/2017 02:26AM Last Post by o_lampe
just a quick connector question by chris33	575	3	05/07/2017 04:21PM Last Post by dc42
(small) Feature request by unromeo21	613	20	05/07/2017 08:06AM Last Post by roboprint
Duet 0.6 Burnt EO Heater Ground Now No Web Control Access by DRTak	604	5	05/05/2017 11:47PM Last Post by DRTak
Suggested Mosfet for Duet 0.8.5 by Nylkos	1,262	2	05/02/2017 05:11PM Last Post by dc42
DUET with IR sensor by selva_tvi	1,142	4	05/02/2017 05:00PM Last Post by dc42
Panel Due brightness control by JuJuDelta	643	5	04/30/2017 01:29PM Last Post by JuJuDelta
Probe triggered and don't stop by DeathmannX	1,542	7	04/27/2017 12:35PM Last Post by ElmoC
S3D skirt/brim with M572 active by unromeo21	582	1	04/25/2017 03:37PM Last Post by unromeo21
Different motor temperatures in serial connection by drmaestro	456	4	04/25/2017 03:03AM Last Post by dc42
Dual extrusion with Single extruder by selva_tvi	788	3	04/24/2017 01:46AM Last Post by selva_tvi
Edit heightmap.csv? [Bug?] by o_lampe	1,574	6	04/23/2017 03:40PM Last Post by dc42
Upgrading to PT100 by drmaestro	634	4	04/23/2017 03:31PM Last Post by dc42
Power failure, Print pause - Resume by selva_tvi	2,297	6	04/23/2017 05:02AM Last Post by dc42
Duet stopped mid print, doesn'T work anymore..... by drmaestro	963	10	04/21/2017 05:08PM Last Post by dc42
Question for DC42 by lolocaledo	716	8	04/21/2017 04:59PM Last Post by dc42
external sd/usb slot by Napalm1432	488	4	04/21/2017 04:57PM Last Post by dc42
Setting Z offset for printing by drmaestro	18,483	7	04/17/2017 02:58PM Last Post by dc42

Page 9 of 25 Pages:

7 8910 11