Welcome! Log In Create A New Profile

Advanced

Dutch User Group - Archive

http://reprap.org/wiki/RUG/Netherlands 
Page 2 of 14    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post
This topic has been moved.

[MTB3D] Filament 19.95 per rol

by MTB3D 		    This topic has been moved.
This topic has been moved.

weet niet waar te beginnen

by Bennyr 		    This topic has been moved.
This topic has been moved.

End stops werken niet. Attachments

by Jochem Elf 		    This topic has been moved.
This topic has been moved.

Prusa i3 (graber) + voorstellen

by sander91 		    This topic has been moved.
This topic has been moved.

printer lashmaze resultaten

by [email protected] 		    This topic has been moved.
This topic has been moved.

extruder stopt ineens Attachments

by Ton_Crazy 		    This topic has been moved.
This topic has been moved.

Thermal Glue voor Thermistors?

by Ohmarinus 		    This topic has been moved.
This topic has been moved.

Golfjes in prints

by spekkie2002 		    This topic has been moved.
This topic has been moved.

Misschien een goed idee? PCB bibliotheek?

by 3D rob 		    This topic has been moved.
This topic has been moved.

Misumi 20x20

by Evbeurdn 		    This topic has been moved.

Beginnende RepRapper heeft hulp nodig.

by steven010 		790 4 04/05/2014 07:10PM
Last Post by Ohmarinus

verschil in filament

by 3Design 		633 2 04/03/2014 05:51AM
Last Post by jonnie

Volgorde XYZ-as bij 'homing'

by WernerDe 		913 4 04/03/2014 04:27AM
Last Post by WernerDe

Cura 13-12 Vs. 14-03

by Mechanic 		879 10 04/02/2014 03:25PM
Last Post by Absrnd

PEEK extruder part buddaschnozzle

by laserboy 		565 5 04/01/2014 01:35PM
Last Post by laserboy

Hulp gevraagd

by Kiekeboe 		939 18 04/01/2014 11:48AM
Last Post by Wvantoorn

Geen constant hoeveelheid pla tijdens printen

by Daan 		578 3 03/31/2014 11:43AM
Last Post by Wvantoorn

Z-as probleem na installatie auto bed leveling

by Segaar 		640 1 03/28/2014 07:30PM
Last Post by Segaar

Hij print !! Attachments

by ColinEnMarwijn 		628 3 03/26/2014 03:01PM
Last Post by Wvantoorn

De eerste prints Attachments

by Lisal27 		1,042 8 03/26/2014 01:31PM
Last Post by Daan

Motor loop richting en end stop positie in Marlin

by Jochem Elf 		758 4 03/26/2014 12:49PM
Last Post by Jochem Elf

Filament & meer: weer testers gezocht Attachments

by jonnie 		1,382 19 03/25/2014 04:26PM
Last Post by jonnie

3D Builder Dual Feed

by Motormuis76 		703 3 03/25/2014 07:55AM
Last Post by Wvantoorn

Beginner loopt vast: Stepper motor Vref? confused smiley Attachments

by Jochem Elf 		4,604 19 03/24/2014 12:38PM
Last Post by Jochem Elf

z-as wilt niet volledig zakken

by 3Design 		744 20 03/23/2014 04:26PM
Last Post by Wvantoorn

Bertsjuhn's Prusa i3 3D printert   (Pages: 1 2 3)

by Bertsjuhn 		2,460 71 03/22/2014 07:38AM
Last Post by [email protected]

leverancier gezocht Filamenten en 3D printers met dubbele kop

by Dijk 		783 9 03/22/2014 06:14AM
Last Post by Dijk

Filament & Meer Eindelijk!!!   (Pages: 1 2)

by Calis 		2,260 36 03/21/2014 03:22PM
Last Post by Evbeurdn

Nog reprappers uit her Oosten des lands aanwezig?

by Wvantoorn 		548 3 03/19/2014 06:40PM
Last Post by Duckpower

Print gaat eerste paar mm uitstekend daarna gaat de Z-as haperen.

by mosoft 		1,118 17 03/19/2014 12:41PM
Last Post by mosoft
Page 2 of 14    Pages: Previous12345NextLast