Welcome! Log In Create A New Profile

Dutch User Group - Archive

http://reprap.org/wiki/RUG/Netherlands

Page 3 of 14 Pages:

1 234 5

Forum List New Topic RSS

	Views	Posts	Last Post
Na een paar millimeter/lagen gaat printje alsnog fout by sassonie	785	14	03/19/2014 05:54AM Last Post by Wvantoorn
Nozzle uitboren by Replace	1,169	14	03/19/2014 04:12AM Last Post by Replace
Zelfbouw 3d printer by 3Design	717	3	03/19/2014 12:17AM Last Post by Wvantoorn
Hobbed bolt maakt draad stuk by jurgendeleeuw	826	8	03/18/2014 04:13PM Last Post by jonnie
Z-as by Daan	883	15	03/17/2014 06:55AM Last Post by Wvantoorn
Aluminium laten Lasersnijden in NL by Ohmarinus	4,074	22	03/15/2014 05:27PM Last Post by Ohmarinus
Anti Warp Technieken in design by Replace	650	11	03/13/2014 05:34PM Last Post by Duckpower
Langzaam maar zeker de geboorte van een i3 printer (Pages: 1 2 3 4 5) by SnelleD	4,864	131	03/12/2014 05:09PM Last Post by Evbeurdn
Layers komen niet recht op elkaar by NijsKei	602	7	03/10/2014 06:25PM Last Post by NijsKei
Hulp bij afstellen prusa i3 by vatam	1,234	9	03/10/2014 03:50AM Last Post by vatam
Bed temperatuur uitzetten na afloop print by Replace	527	5	03/09/2014 02:40PM Last Post by Replace
Eenlaags ontwerp niet manifold by Replace	430	2	03/08/2014 03:42PM Last Post by Replace
configuratie van marlin op megatronics V2.0 by Daan	1,062	4	03/07/2014 05:21PM Last Post by NijsKei
Prusa i3 Rookie (Pages: 1 2 3) by Hill	2,709	84	03/07/2014 04:28PM Last Post by NijsKei
Z as beweegt niet meer tijdens printen. by Lisal27	686	15	03/07/2014 03:19PM Last Post by Evbeurdn
mendelmax 1.5+ marlin by jurgendeleeuw	664	7	03/07/2014 03:08PM Last Post by Evbeurdn
cable track by 3Design	494	6	03/06/2014 06:35PM Last Post by Ohmarinus
Welke diameter filament wordt het meeste gebruikt. by Lisal27	1,514	25	03/06/2014 12:51AM Last Post by Replace
nema 23 by massimo	1,128	2	03/05/2014 04:11PM Last Post by Ohmarinus
Hoeveel meter op een spoel ? by Replace	6,953	5	03/04/2014 05:33AM Last Post by Bertsjuhn
pla komt steeds los by Daan	1,374	10	03/03/2014 05:57PM Last Post by Evbeurdn
Prototype bouwen voor werk (Pages: 1 2) by delchrys	1,437	43	03/02/2014 08:05PM Last Post by delchrys
3dexpo 2014 - Prague, Czech Republic by P3T3	540	1	02/28/2014 03:25AM Last Post by P3T3
Servo aansluiting by -DUS-	522	2	02/27/2014 05:44PM Last Post by Ohmarinus
Difference functie in OpenScad... geeft complement by Replace	557	6	02/25/2014 03:51PM Last Post by Replace
Filament by 3Design	1,126	14	02/25/2014 03:43PM Last Post by Ohmarinus
Volgende project (Pages: 1 2) by Evbeurdn	3,628	48	02/20/2014 09:16AM Last Post by aloys
Voorstellen en ideeen voor Large Prusa by ColinEnMarwijn	897	10	02/19/2014 03:55PM Last Post by ColinEnMarwijn
Kapton opschuren by Ohmarinus	720	11	02/18/2014 08:41AM Last Post by Replace
3D Builder by roach	1,097	12	02/18/2014 04:36AM Last Post by Ohmarinus

Page 3 of 14 Pages:

1 234 5

Dutch User Group - Archive

Langzaam maar zeker de geboorte van een i3 printer (Pages: 1 2 3 4 5)

Prusa i3 Rookie (Pages: 1 2 3)

Prototype bouwen voor werk (Pages: 1 2)

Volgende project (Pages: 1 2)