Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 09:37AM |
Admin Registered: 17 years ago Posts: 7,881 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 12:53PM |
Registered: 11 years ago Posts: 93 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 01:25PM |
Registered: 11 years ago Posts: 45 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 01:32PM |
Registered: 11 years ago Posts: 93 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 03:08PM |
Registered: 11 years ago Posts: 45 |
Quote
Justintime
@p40
What extruder do you use then?? I am on a wades...
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 04:40PM |
Registered: 11 years ago Posts: 93 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 05:45PM |
Registered: 11 years ago Posts: 45 |
Quote
Justintime
Nice nice that looks very clean.....
So it's better than the wades? Or still in test mode?
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 15, 2013 09:22PM |
Admin Registered: 17 years ago Posts: 7,881 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 12:24AM |
Admin Registered: 12 years ago Posts: 1,063 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 03:21AM |
Registered: 11 years ago Posts: 93 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 04:02AM |
Admin Registered: 12 years ago Posts: 1,063 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 01:42PM |
Registered: 11 years ago Posts: 210 |
Quote
Justintime
But the big question is..... By which speed are the bolds slipping?
At the moment my speed is approx 150mm/sec. Before the filament is slipping.
But I will definitely will make that direct extruder.... Even it's only for the looks....
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 03:12PM |
Admin Registered: 12 years ago Posts: 1,063 |
Quote
greenman100
Quote
Justintime
But the big question is..... By which speed are the bolds slipping?
At the moment my speed is approx 150mm/sec. Before the filament is slipping.
But I will definitely will make that direct extruder.... Even it's only for the looks....
I can do 225mm/s without slip, direct drive.
150mm/s is slow, not fast.
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 07:22PM |
Registered: 12 years ago Posts: 544 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 16, 2013 07:35PM |
Registered: 11 years ago Posts: 210 |
Quote
aduy
when you say 220mm/s that means nothing, what is the input speed relative to the filament, whats the nozzle size and layer height? the fastest i can run my machine currently is 15mm/s of 1.75mm filament into the hotend.
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 20, 2013 11:46AM |
Registered: 11 years ago Posts: 40 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 27, 2013 02:35PM |
Registered: 11 years ago Posts: 553 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 27, 2013 03:11PM |
Registered: 11 years ago Posts: 52 |
Quote
greenman100
Quote
aduy
when you say 220mm/s that means nothing, what is the input speed relative to the filament, whats the nozzle size and layer height? the fastest i can run my machine currently is 15mm/s of 1.75mm filament into the hotend.
I said 225mm/s, and I'm not sure it "means nothing".
Anyway: 0.4mm nozzle, 0.3mm layer heights. Looks like around 14mm/sec of 1.75mm filament past the extruder.
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 27, 2013 06:51PM |
Registered: 12 years ago Posts: 544 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 29, 2013 06:05PM |
Registered: 11 years ago Posts: 52 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 30, 2013 01:05AM |
Registered: 11 years ago Posts: 210 |
Quote
cope413
Not sure where that came from...
All I was saying was that posting speed settings without also posting jerk/accel firmware settings was meaningless.
Everyone is very impressed with your amazingly rigid and fast cartesian bot... at least everyone who doesn't have a delta bot.
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] November 30, 2013 11:34AM |
Registered: 13 years ago Posts: 118 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 01, 2013 08:23PM |
Registered: 11 years ago Posts: 52 |
Quote
greenman100
Quote
cope413
Not sure where that came from...
All I was saying was that posting speed settings without also posting jerk/accel firmware settings was meaningless.
Everyone is very impressed with your amazingly rigid and fast cartesian bot... at least everyone who doesn't have a delta bot.
Yeah jerk and accel of 1.
Its hitting 225mm/s. I'm quite familiar with acceleration and jerk. It is not 225mm/s desired, it is hitting 225mm/s actual.
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 02, 2013 12:58AM |
Registered: 11 years ago Posts: 39 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 02, 2013 04:19AM |
Registered: 12 years ago Posts: 544 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 02, 2013 09:04AM |
Registered: 11 years ago Posts: 553 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 03, 2013 08:40AM |
Registered: 11 years ago Posts: 13 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 03, 2013 10:04AM |
Registered: 13 years ago Posts: 118 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 04, 2013 12:44AM |
Registered: 11 years ago Posts: 341 |
Re: Update on the E3D All Metal Hotend (Now finally shipping!) [Lots of pictures] December 04, 2013 01:45AM |
Registered: 11 years ago Posts: 13 |