Welcome! Log In Create A New Profile

Advanced

What is this board ?

Posted by tchitchou 
Forum List Message List New Topic
Ohmarinus
Re: What is this board ?
March 01, 2015 05:42AM
Just to be sure, did you select it in the tools > boards list?

I think the ATmega644 is the correct one btw.

This is what my Arduino software looks like, I don't have the Sanguino drivers installed though because I'm running from Ramps 1.4:


http://www.marinusdebeer.nl/
Reply Quote
tchitchou
Re: What is this board ?
March 01, 2015 06:56AM
Quote
Ohmarinus
Just to be sure, did you select it in the tools > boards list?
I think the ATmega644 is the correct one btw.

Yep. Since the biginning.

And I see the 3 sanguino boards, now, with the arduino 1.6.0 ( plus the 0023r3 version in the good folder)



Just tried again with the ATmega644 and I have this error message :
"Third-party platform.txt does not define compiler.path. Please report this to the third-party hardware maintainer."
"le paramètre de configuration « recipe.cpp.o.pattern » missing..

Edited 1 time(s). Last edit at 03/01/2015 06:56AM by tchitchou.
Reply Quote
Ohmarinus
Re: What is this board ?
March 01, 2015 07:54AM
OKay, btw, the correct board is number 62! Not 6.

http://www.marinusdebeer.nl/
Reply Quote
tchitchou
Re: What is this board ?
March 01, 2015 08:06AM
Ok.

Tried too, same error message.



I've tried to make a search in my folders, "*recipe*.*", not a thing..
Reply Quote
tchitchou
Re: What is this board ?
March 01, 2015 11:23AM
Sorry if I insist, but..
Quote
tchitchou
Quote
billober33974
Is the big chip on the board a ATmega2560?
Yep !

Can the board be a sanguino, then ?
Reply Quote
Ohmarinus
Re: What is this board ?
March 01, 2015 04:01PM
Well look at the specs of this baby:
[reprap.org]

Also Sanguino compatible. And it uses that chip. So yes it's possible.

It could be a modified 3Drag board?

In your motherboard list the 3Drag printer is number 77 I see. Maybe it works?

If it doesn't, maybe there is something wrong with the package that you downloaded. You could try to get a fresh package without anything preconfigured.

Edited 2 time(s). Last edit at 03/01/2015 04:08PM by Ohmarinus.

http://www.marinusdebeer.nl/
Reply Quote
tchitchou
Re: What is this board ?
March 06, 2015 02:26PM
Hi !
A last message, I found it !
I looked a lot of rostocks on chinese sites, contacted sellers, downloaded a lot of files.. And among the PDF, I found my board !
I still don't know the name, but there is the wiring, and the firmware smiling smiley



I have now the little problems of anybody who begin with a 3d printer smiling smiley

Here is the link, may be someone will need it, as I did.
chinese rostock package

Thank you all
Reply Quote
Ohmarinus
Re: What is this board ?
March 06, 2015 07:03PM
W00t! Finally smiling smiley

Congratulations.

http://www.marinusdebeer.nl/
Reply Quote
[email protected]
Re: What is this board ?
March 15, 2015 05:13PM
please help!
I have a problem of post 79? Board melzi 2.0, when compiling issued such an error, the driver tried to change but it may not lead to anything, in the compiler choose Sanguino in W/ ATmega1284p 16mgz
please advise decision
Reply Quote
Bobyni
Re: What is this board ?
April 08, 2015 02:17AM
Clone of SAINSMART 2in1 Ramos 1.4 board ???
Reply Quote
Attachments:
open | download - image.jpg (585.3 KB)
Page 2 of 2    Pages: Previous12
Newer Topic Older Topic
Sorry, only registered users may post in this forum.

Click here to login