Power Supply not starting?
Posted by Steven Rude
|
Power Supply not starting? August 20, 2016 11:01AM |
Registered: 7 years ago Posts: 15 |
I finally have the dual extruder assembled, and ready to go, I think.
I plugged it in to the 110 outlet, with switch set to 110. Plugged the usb into the computer,
Nothing has booted, Nothing on the power supply, and nothing has popped up under devices in window 8.1
Any advice?
Regards
Steven
I plugged it in to the 110 outlet, with switch set to 110. Plugged the usb into the computer,
Nothing has booted, Nothing on the power supply, and nothing has popped up under devices in window 8.1
Any advice?
Regards
Steven
|
Re: Power Supply not starting? August 20, 2016 11:57AM |
Admin Registered: 12 years ago Posts: 6,859 |
Lots more details required
What type of power supply? ATX type or LED type?
How is the power supply set to turn on? via the controller or on all the time?
What type of reprap controller?
Has this ever worked? ie was this an upgrade to dual extruder from a working single extruder machine?
Edited 1 time(s). Last edit at 08/20/2016 11:57AM by Dust.
What type of power supply? ATX type or LED type?
How is the power supply set to turn on? via the controller or on all the time?
What type of reprap controller?
Has this ever worked? ie was this an upgrade to dual extruder from a working single extruder machine?
Edited 1 time(s). Last edit at 08/20/2016 11:57AM by Dust.
|
Re: Power Supply not starting? August 20, 2016 01:32PM |
Registered: 7 years ago Posts: 15 |
Thank you for your response.
Here is a photo of the power supply. No documentation, not sure the type.
It is a dual extruder kit, not an upgrade.
I have just assembled the unit, it is the first time getting things started.
I am not sure which controller board, but I have attached a photo.
I pushed the little reset button on the side of the controller card, with no results.
ThanX again for your help
Regards
Steven
Here is a photo of the power supply. No documentation, not sure the type.
It is a dual extruder kit, not an upgrade.
I have just assembled the unit, it is the first time getting things started.
I am not sure which controller board, but I have attached a photo.
I pushed the little reset button on the side of the controller card, with no results.
ThanX again for your help
Regards
Steven
|
Re: Power Supply not starting? August 20, 2016 01:41PM |
Registered: 8 years ago Posts: 893 |
|
Re: Power Supply not starting? August 20, 2016 02:25PM |
Registered: 7 years ago Posts: 15 |
|
Re: Power Supply not starting? August 20, 2016 03:19PM |
Registered: 7 years ago Posts: 15 |
|
Re: Power Supply not starting? August 20, 2016 03:28PM |
Registered: 7 years ago Posts: 15 |
|
Re: Power Supply not starting? August 20, 2016 03:38PM |
Registered: 7 years ago Posts: 15 |
|
Re: Power Supply not starting? August 20, 2016 04:02PM |
Registered: 7 years ago Posts: 15 |
I have now, hooked up post 3 and 6 with the sensor and fan leeds.
The Led light for the power supply is still going on.
Then I re connected the red on post 1 and black on post 4.
No Led on the power supply.
The problem, maybe the connections that power 1 and 4 post drive.
What next? To Check
The Led light for the power supply is still going on.
Then I re connected the red on post 1 and black on post 4.
No Led on the power supply.
The problem, maybe the connections that power 1 and 4 post drive.
What next? To Check
|
Re: Power Supply not starting? August 20, 2016 05:13PM |
Registered: 7 years ago Posts: 15 |
Just when I thought this was the problem.
The 2 wires from the heating plate, going into the blue terminal. I re hooked them up, one side of the terminal plastic is crushed, a bit.
However, I think the connections are good.
But when I connect 1 red and 4 black post to the power supply. The LED on the power supply is still not lighting up.
The 2 wires from the heating plate, going into the blue terminal. I re hooked them up, one side of the terminal plastic is crushed, a bit.
However, I think the connections are good.
But when I connect 1 red and 4 black post to the power supply. The LED on the power supply is still not lighting up.
|
Re: Power Supply not starting? August 20, 2016 05:22PM |
Registered: 7 years ago Posts: 15 |
|
Re: Power Supply not starting? August 20, 2016 10:05PM |
Admin Registered: 12 years ago Posts: 6,859 |
where does the wires "1+ and 4-" on the supply go to?
I suspect they go to power pins 3 and 4 on the Green plug. This would be the power for the heated bed.
What you have is known a a LED power supply, it should always be on when mains is applied, unless there is a short.
Your controller is a ramps
Please take a photo of the heated bed (top view with any connection information) and secondly a photo of how the wires are connected to the heated bed.
I suspect they go to power pins 3 and 4 on the Green plug. This would be the power for the heated bed.
What you have is known a a LED power supply, it should always be on when mains is applied, unless there is a short.
Your controller is a ramps
Please take a photo of the heated bed (top view with any connection information) and secondly a photo of how the wires are connected to the heated bed.
|
Re: Power Supply not starting? August 22, 2016 10:10AM |
Registered: 7 years ago Posts: 15 |
Good Morning,
Yes 1+ and 4- go to 3 and 4 on the board.
I took the wires off the blue terminal, going to the heating bed.
Then attached 1+ and 4-, and still no LED on.
The short lies in the boards? The blue terminal on the plus side was damage a bit when first attaching the wire. HHUUMM.
Picture showing the wires attached to the bed from the blue terminal.
Can the bed be directly connected to the power supply?
Thank you for your help Mistro.
Yes 1+ and 4- go to 3 and 4 on the board.
I took the wires off the blue terminal, going to the heating bed.
Then attached 1+ and 4-, and still no LED on.
The short lies in the boards? The blue terminal on the plus side was damage a bit when first attaching the wire. HHUUMM.
Picture showing the wires attached to the bed from the blue terminal.
Can the bed be directly connected to the power supply?
Thank you for your help Mistro.
|
Re: Power Supply not starting? August 22, 2016 05:53PM |
Admin Registered: 12 years ago Posts: 6,859 |
|
Re: Power Supply not starting? August 24, 2016 10:04PM |
Registered: 7 years ago Posts: 318 |
Sorry, only registered users may post in this forum.