New cheap printer October 06, 2016 02:26AM |
Registered: 8 years ago Posts: 193 |
Re: New cheap printer October 06, 2016 04:33AM |
Registered: 12 years ago Posts: 528 |
Re: New cheap printer October 06, 2016 06:23AM |
Registered: 8 years ago Posts: 26 |
Re: New cheap printer October 06, 2016 09:23AM |
Registered: 9 years ago Posts: 131 |
Re: New cheap printer October 06, 2016 12:04PM |
Registered: 8 years ago Posts: 26 |
Re: New cheap printer October 06, 2016 12:30PM |
Registered: 9 years ago Posts: 131 |
Re: New cheap printer October 06, 2016 01:52PM |
Registered: 8 years ago Posts: 26 |
Re: New cheap printer October 06, 2016 01:57PM |
Registered: 8 years ago Posts: 193 |
Quote
Viper97
I picked up this one and it arrived last night. Opened it up and found that it was well packed. There were directions but they were mostly a parts listing and not assembly directions. No problem, the Geeetech Wiki has assembly instructions in PDF form so I downloaded it.
I did take a look at the acrylic parts and they seem to be cut well with no sharp edges. Mine came with the all metal X-axis as it is the Pro B. The heated bed is already soldered for 12V, the hot end is assembled. The power supply provided is a 12V 15A with a default setting of 220V.
While I haven't assembled it just yet as I am working on rebuilding my Prusa I3 Steel I am looking forward to testing it. Oh, it came with a RAMPS all-in-one board which is the Geeetech GT 2650.
Re: New cheap printer October 06, 2016 03:54PM |
Registered: 9 years ago Posts: 131 |
Quote
Suggy
Quote
Viper97
I picked up this one and it arrived last night. Opened it up and found that it was well packed. There were directions but they were mostly a parts listing and not assembly directions. No problem, the Geeetech Wiki has assembly instructions in PDF form so I downloaded it.
I did take a look at the acrylic parts and they seem to be cut well with no sharp edges. Mine came with the all metal X-axis as it is the Pro B. The heated bed is already soldered for 12V, the hot end is assembled. The power supply provided is a 12V 15A with a default setting of 220V.
While I haven't assembled it just yet as I am working on rebuilding my Prusa I3 Steel I am looking forward to testing it. Oh, it came with a RAMPS all-in-one board which is the Geeetech GT 2650.
Whitch one did you get and from where and the cost of you dont mind me asking
Re: New cheap printer October 06, 2016 06:35PM |
Registered: 12 years ago Posts: 5,794 |
Re: New cheap printer October 08, 2016 05:48AM |
Registered: 8 years ago Posts: 193 |
Re: New cheap printer October 08, 2016 08:15AM |
Registered: 12 years ago Posts: 5,794 |
Re: New cheap printer October 08, 2016 03:12PM |
Registered: 8 years ago Posts: 193 |
Re: New cheap printer October 08, 2016 04:23PM |
Registered: 10 years ago Posts: 293 |
Re: New cheap printer October 09, 2016 06:49AM |
Registered: 9 years ago Posts: 131 |
Re: New cheap printer October 10, 2016 10:10AM |
Registered: 8 years ago Posts: 193 |
Re: New cheap printer October 10, 2016 10:37AM |
Registered: 9 years ago Posts: 131 |
Re: New cheap printer October 10, 2016 10:54AM |
Registered: 8 years ago Posts: 193 |
Re: New cheap printer October 10, 2016 11:20AM |
Registered: 8 years ago Posts: 9 |
Re: New cheap printer October 10, 2016 11:58AM |
Registered: 9 years ago Posts: 131 |
Re: New cheap printer October 11, 2016 11:18AM |
Registered: 8 years ago Posts: 28 |