Scared about my Anet a8 order April 05, 2017 04:55PM |
Registered: 7 years ago Posts: 9 |
Re: Scared about my Anet a8 order April 05, 2017 06:25PM |
Registered: 9 years ago Posts: 3,525 |
Re: Scared about my Anet a8 order April 05, 2017 07:07PM |
Registered: 9 years ago Posts: 601 |
Re: Scared about my Anet a8 order April 05, 2017 07:15PM |
Registered: 8 years ago Posts: 94 |
Re: Scared about my Anet a8 order May 15, 2017 08:53PM |
Registered: 7 years ago Posts: 9 |
Re: Scared about my Anet a8 order May 16, 2017 06:05AM |
Registered: 9 years ago Posts: 3,525 |
Re: Scared about my Anet a8 order May 16, 2017 09:09AM |
Registered: 7 years ago Posts: 270 |
Re: Scared about my Anet a8 order May 16, 2017 01:08PM |
Registered: 10 years ago Posts: 893 |
Re: Scared about my Anet a8 order May 16, 2017 01:51PM |
Registered: 7 years ago Posts: 270 |
Quote
David J
Quote
newbob
Consider stuffing power supply and board into a metal enclosure to stop potential fire from spreading:
Not sure if you're serious or not - but unless you let lots of air into the enclosure it's going to overheat and burn anyway!
Re: Scared about my Anet a8 order May 17, 2017 04:07AM |
Registered: 7 years ago Posts: 154 |
Quote
newbob
...
Yes, by all means, you have to use forced air cooling if you stuff it in any type of enclosure.
Re: Scared about my Anet a8 order May 17, 2017 05:42AM |
Registered: 10 years ago Posts: 893 |
Quote
Dancer
Buy reliable parts, do a clean setup, install a smoke detector, place a fire extinguisher where you can grab it.
If you are really worried - do not leave it allone.
And if you even can't trust it this way: Just don't buy a 3D-Printer.
Re: Scared about my Anet a8 order May 17, 2017 11:37AM |
Registered: 7 years ago Posts: 270 |
Quote
Dancer
Quote
newbob
...
Yes, by all means, you have to use forced air cooling if you stuff it in any type of enclosure.
And if you do this, you are delivering fresh Oxygen to the fire and spreading it out of the Box again.
Never heard anything more stupid like your Suggestion.
Sorry.
Buy reliable parts, do a clean setup, install a smoke detector, place a fire extinguisher where you can grab it.
If you are really worried - do not leave it allone.
And if you even can't trust it this way: Just don't buy a 3D-Printer.
Re: Scared about my Anet a8 order May 17, 2017 01:45PM |
Registered: 9 years ago Posts: 601 |
Re: Scared about my Anet a8 order May 17, 2017 06:46PM |
Registered: 10 years ago Posts: 978 |
Quote
Dancer
Quote
newbob
...
Yes, by all means, you have to use forced air cooling if you stuff it in any type of enclosure.
And if you do this, you are delivering fresh Oxygen to the fire and spreading it out of the Box again.
Never heard anything more stupid like your Suggestion.
Sorry.
I do agree with this part.Quote
Buy reliable parts, do a clean setup, install a smoke detector, place a fire extinguisher where you can grab it.
If you are really worried - do not leave it allone.
And if you even can't trust it this way: Just don't buy a 3D-Printer.
Re: Scared about my Anet a8 order May 17, 2017 07:28PM |
Registered: 8 years ago Posts: 558 |