Re: Precision Piezo Z-probe Now available. July 26, 2018 04:14AM |
Registered: 9 years ago Posts: 487 |
Quote
Thanks for the help, and I have it responding now. But in an unusual manner. When I type M30 it drops down 400 mm andit won't stop. After that it slows down and makes several random moves. Next it moves to X0 Y0 and probes. It then moves randomly for 3 more moves and comes back to X0 Y0 and Z35, which is accurate. I have been told my firmware needs to be updated. So that's where I am going next.
Re: Precision Piezo Z-probe Now available. July 26, 2018 07:26AM |
Registered: 11 years ago Posts: 14,685 |
Quote
Moriquendi
.... I don't think it's fair to say that dc42 was not helpful, he's trying to help and making useful suggestions but these things can take a little time, have patience.
Re: Precision Piezo Z-probe Now available. July 27, 2018 08:44AM |
Registered: 7 years ago Posts: 60 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 11:14AM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 11:29AM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 11:55AM |
Registered: 10 years ago Posts: 77 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:10PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:24PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:41PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:46PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:46PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 12:50PM |
Registered: 10 years ago Posts: 465 |
Quote
cwaa
Dc42 was not helpful. He recommended removing the z-probe deploy and retract files. When I did, my machine when given a G30, would hammer the tower endstops until I shut it down. I put those files back and my printer again was operational. I believe I have a defective Orion module. I have asked to return it, we will see what the response is.
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:06PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:16PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:19PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:19PM |
Registered: 7 years ago Posts: 60 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:20PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:21PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:24PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:28PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:30PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:31PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:34PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:34PM |
Registered: 9 years ago Posts: 3,525 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:38PM |
Registered: 10 years ago Posts: 465 |
Wasn't planning on keeping it that way, just using the Pi to test the sensor design for sensitivity, considering that the Duet is in a box, and the printer that I plan to use it on is currently entirely vaporware. I figure that if the sensors work as designed, then I go ahead. If not, it's easy enough to change them now, and make appropriate design changes to the printer. Mostly I'm not sure about the use of springs in the system. I suppose that I shouldn't really need much of a leveling mechanism with auto-leveling, though I'd like to have some adjustment possible.Quote
DjDemonD
Supraguy, you can get 3.3v off the duet. Not sure why the raspi is needed in the system?
Re: Precision Piezo Z-probe Now available. July 27, 2018 01:50PM |
Registered: 11 years ago Posts: 14,685 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 02:01PM |
Registered: 9 years ago Posts: 487 |
Quote
I have now ordered another Orion and have asked for directions on how to return the first one. So far I have not received any answer.
Re: Precision Piezo Z-probe Now available. July 27, 2018 02:18PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 02:23PM |
Registered: 8 years ago Posts: 257 |
Re: Precision Piezo Z-probe Now available. July 27, 2018 02:31PM |
Registered: 9 years ago Posts: 487 |