MKS GEN V1.4 & MKS TFT32 asking for help. September 25, 2017 12:37PM |
Registered: 7 years ago Posts: 8 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 25, 2017 04:18PM |
Admin Registered: 13 years ago Posts: 7,123 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 26, 2017 03:43AM |
Registered: 7 years ago Posts: 8 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 26, 2017 04:11AM |
Admin Registered: 13 years ago Posts: 7,123 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 26, 2017 04:25AM |
Registered: 7 years ago Posts: 8 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 26, 2017 04:58AM |
Admin Registered: 13 years ago Posts: 7,123 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 26, 2017 05:35AM |
Registered: 7 years ago Posts: 8 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. September 27, 2017 04:02AM |
Registered: 7 years ago Posts: 8 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. November 17, 2017 11:36PM |
Registered: 7 years ago Posts: 35 |
Re: MKS GEN V1.4 & MKS TFT32 asking for help. November 18, 2017 02:38AM |
Registered: 12 years ago Posts: 528 |
Quote
firefly
I enabled all seven of the "More" buttons. They all work fine. Then I replaced the command for the first one button (which had "G28 X0") with "M18 X0", which disables steppers. It didn't work - pressing the button just locks the LCD for a bit, then it comes back to being responsive again. The M18 command works through Prontoface though.
Re: MKS GEN V1.4 & MKS TFT32 asking for help. November 18, 2017 11:29AM |
Registered: 7 years ago Posts: 35 |
Quote
jinx
Quote
firefly
I enabled all seven of the "More" buttons. They all work fine. Then I replaced the command for the first one button (which had "G28 X0") with "M18 X0", which disables steppers. It didn't work - pressing the button just locks the LCD for a bit, then it comes back to being responsive again. The M18 command works through Prontoface though.
could it be because its already there under the set section so its ignoring the user options, be sure to have the latest V3 firmware. could be you found one off the quirks with these controllers!
Re: MKS GEN V1.4 & MKS TFT32 asking for help. November 18, 2017 02:27PM |
Registered: 12 years ago Posts: 528 |
could be that not all styles are being updated equallyQuote
firefly
I couldn't find anything in the menus that would indicate unlock/release/off steppers/motors, so I don't think the M18 command is being repeated.
Re: MKS GEN V1.4 & MKS TFT32 asking for help. November 18, 2017 03:22PM |
Registered: 7 years ago Posts: 35 |