New to 3D printing, some help is needed, please January 05, 2020 01:12PM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 05, 2020 02:14PM |
Registered: 12 years ago Posts: 2,470 |
Re: New to 3D printing, some help is needed, please January 05, 2020 05:31PM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 06, 2020 02:02AM |
Registered: 12 years ago Posts: 2,470 |
Re: New to 3D printing, some help is needed, please January 06, 2020 08:43AM |
Registered: 6 years ago Posts: 1,863 |
Re: New to 3D printing, some help is needed, please January 06, 2020 09:45AM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 07, 2020 07:30AM |
Registered: 8 years ago Posts: 413 |
Re: New to 3D printing, some help is needed, please January 07, 2020 07:53AM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 07, 2020 09:56PM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 08, 2020 09:34AM |
Registered: 6 years ago Posts: 1,863 |
Re: New to 3D printing, some help is needed, please January 09, 2020 05:12AM |
Admin Registered: 11 years ago Posts: 3,096 |
Re: New to 3D printing, some help is needed, please January 09, 2020 07:02AM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 09, 2020 07:29AM |
Admin Registered: 11 years ago Posts: 3,096 |
Quote
jdebuhr
Thanks for the tip. I found that the hot end was leaking, so I am waiting on parts to replace the pieces. I will set it up and try again. Here is a picture of the bottom, not sure if the lighting is any better though
Re: New to 3D printing, some help is needed, please January 09, 2020 08:01AM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 09, 2020 09:43AM |
Admin Registered: 11 years ago Posts: 3,096 |
Quote
jdebuhr
Do the print starts at .3mm from the bed. Like I said I have pieces coming to have extras and yeah planned on heating it to tighten it fully.. then try again..
Re: New to 3D printing, some help is needed, please January 14, 2020 10:48PM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 15, 2020 10:30AM |
Registered: 7 years ago Posts: 619 |
Quote
jdebuhr
After a week of getting pieces and reassembling. I printed 2 objects. Another cube and 3DBenchy. I used painters tape on the bed and it stuck to the objects. I will try glue sticks next
Re: New to 3D printing, some help is needed, please January 15, 2020 11:35AM |
Registered: 4 years ago Posts: 77 |
Re: New to 3D printing, some help is needed, please January 15, 2020 05:18PM |
Registered: 7 years ago Posts: 619 |
Quote
jdebuhr
Sounds like with a heated bed and PLA just use Hairspray? or are you just using hairspray for the ABS and more exotic stuff?
Thanks I am glad the printer is working well for me now
Re: New to 3D printing, some help is needed, please January 15, 2020 07:04PM |
Registered: 4 years ago Posts: 77 |
Quote
dlc60
The thing is, you need to have your Z end stop right and the bed MUST be flat for anything to print reliably.
DLC
Re: New to 3D printing, some help is needed, please January 16, 2020 11:34AM |
Registered: 7 years ago Posts: 619 |
Quote
jdebuhr
Quote
dlc60
The thing is, you need to have your Z end stop right and the bed MUST be flat for anything to print reliably.
DLC
Yes, I have definitely found that out.. I check bed level first then print. I have been reading about the auto level stuff, just not purchased anything yet.
I do have a glass heated bed. I was also just given a Mini RAMBo 1.3 and a Full Graphic Smart Controller..