How to fix Marlin code to stop extruder's fan when I Pause the print October 25, 2018 01:09AM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 25, 2018 04:06AM |
Admin Registered: 13 years ago Posts: 6,999 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 25, 2018 05:52AM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 25, 2018 06:16AM |
Registered: 5 years ago Posts: 15 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 25, 2018 10:23PM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 26, 2018 04:35AM |
Registered: 6 years ago Posts: 1,007 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 26, 2018 10:48AM |
Registered: 10 years ago Posts: 14,672 |
Quote
MKSA
This request is crazy anyway !
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 26, 2018 01:56PM |
Registered: 6 years ago Posts: 1,007 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 29, 2018 11:30AM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 29, 2018 12:52PM |
Admin Registered: 13 years ago Posts: 6,999 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 29, 2018 04:16PM |
Registered: 6 years ago Posts: 1,007 |
Quote
dc42
Quote
MKSA
This request is crazy anyway !
Why is it crazy to turn the fan off when the print is paused? Users of RepRapFirmware sometimes do this, by adding M106 S0 to the pause.g file on the SD card, and M106 R1 to the resume.g file.
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 29, 2018 04:23PM |
Registered: 6 years ago Posts: 1,007 |
Quote
Dust
DC42 is once again trying to subvert a thread for his own evil ends
He is referring to his own firmware which only runs on 32 bit controller boards (which he also sells)
This is despite the fact that you clearly posted that you want to do this on marlin and not his "reprapfirmware"
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 30, 2018 10:58PM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print October 31, 2018 07:36AM |
Registered: 6 years ago Posts: 1,863 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print November 02, 2018 03:04AM |
Registered: 10 years ago Posts: 12 |
Re: How to fix Marlin code to stop extruder's fan when I Pause the print November 02, 2018 03:09AM |
Registered: 10 years ago Posts: 12 |