Aporia gia commissioning meso pronterface

Geia sas,

Molis teliosa to hardware kommati sto reprap tricolour mendel pou ftiaxnw kai arxisa to "commisioning" stadio kai exw mia mikri aporia pou elpizw kapios na mporei na mou ti lisei..
Oi odigies lene oti mporw na kanw "Get Temp" meso tou ponterface k na parw pisw tis times tis thermokrasias apo to kathe ena apo ta tessera thermistor pou exw (3x extruders kai 1x bed).
Mporei kapios na mou eksigisei to minima pou mou dinei to pronterface?
Ti simainoun oi arithmoi?

Euxaristw.

edit: ksexasa na anaferw oti xrisimopoiw Windows 7 k to precompiled version tou pronterface.

Edited 1 time(s). Last edit at 09/01/2014 03:37PM by katsiniaouros.

To pronterface einai ena GUI (kai oxi mono) gia na "milas" me to hardware tou printer sou. Auto simainei oti prepei na gnorizoume poio firmware exeis. Theorontas oti trexeis Marlin tote oi commands pou mporeis na doseis einai:

T1 gia na epilekseis to extruder 1
T2 gia na epilekseis to extruder 2
T3 gia na epilekseis to extruder 3

Afou kaneis thn epilogh dineis M105 gia na pareis apanthsh me tis thermokrasies
Paradeigma -> T:190 B:65
T = thermokrasia epilegmenou extruder
B = thermokrasia bed

Elpizo na se voithisa alla an mporeis postare kai "tous arithmous"

Euxaristw gia tin apantisi glx51mm!

To M105 mou dinei: ok T0: 141.6/-273.1 T1: -273.0/-273.0 T2: -273.0/-273.0 B:31.1 /-273.1 @:0

Gia Firmware mou leei: Firmware version: V08, EEPROM version: V08

Ti paei lathos? den eprepe oi thermokrasies na einai "dwmatiou"?

Mallon exeis epilegmeno lathos thermistor table.
Sto "configuration.h " tou Marlin sto section "Thermal Settings" mporeis na epilekseis to thermistor pou exeis. Tha prepei omos na gnorizeis to montelo tou thermistor sou.
An mporeis dose kai mia M115 na eimaste sigouroi oti exeis Marlin firmware.

Eixa kai egw tin ipopsia koitazwntas se arketa forums k diaforetika threads oti kati lathos egeine me ta thermistors.
Kserw pio thermistor exw k kserw kai ti na allaksw sto configuration.h.. Apla den eimai sigouros an kserw pws kai pou einai to configuration.h..
Prepei na katevasw to firmware, na kanw tis metatropes, na to kanw compile, k na to ksanakanw upload sto Melzi board? i iparxei pio "efkolos" tropos..?

Oso gia to firmware eimai sxedwn sigouros oti einai Merlin. Apla twra den exw access sto 3d printer.. Tha kanw post molis mporesw..

Ean exeis/theleis Marlin tote nai, i diadikasia einai auth pou perigrafeis. Den iksera oti xrisimopoieis Melzi opote isos na exeis allo firmware. To pio sinithes pleon einai to Ramps 1.4 kai gia auto theorisa oti trexeis Marlin.

Euxaristw gia oli ti voithia!! Telika itan diko mou to lathos (an kai diorthwsa k kapia pragmata sto firmware.. )
Eixa lathos enomena ta kalodia tou prwtou thermistor.. :|
Kai pali euxaristw.

Poion ektipoth exeis btw?

Signwmi pou argisa na apantisw..
Exw to Tri-colour Mendel..

No problem.
Exeis kanei kamia ektyposh ?