CoreXY Stepperanschluss 28. December 2014 12:58 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 229 |
Re: CoreXY Stepperanschluss 28. December 2014 14:49 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 229 |
Re: CoreXY Stepperanschluss 29. December 2014 07:07 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 31 |
Re: CoreXY Stepperanschluss 29. December 2014 08:56 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 4.977 |
Triffid Hunter's Calibration Guide | --> X <-- Drill for new Monitor | Most important Gcode. |
Re: CoreXY Stepperanschluss 29. December 2014 12:20 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 229 |
Quote
angkor
grüss dich
Bist Du sicher, dass die Motoren richtig an das Rumba angehängt sind? Ich hatte das immer, wenn sich eine Ader gelöst hatte. Dann zittert er nur vor sich hin.
gruss angkor
Das ist mir neu, ehrlich gesagt. Was passiert denn, wenn ich das nicht mache? Ich habe bisher die Firmware immer als sketch neu aufgespielt, wenn ich was in der config geändert habe.Quote
M502 M500 nicht vergessen um die neue Config im EEPROM zu überschreiben.
Re: CoreXY Stepperanschluss 29. December 2014 15:22 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 229 |
// Uncomment the following line to enable CoreXY kinematics #define COREXY // coarse Endstop Settings #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #ifndef ENDSTOPPULLUPS // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined // #define ENDSTOPPULLUP_XMAX // #define ENDSTOPPULLUP_YMAX // #define ENDSTOPPULLUP_ZMAX // #define ENDSTOPPULLUP_XMIN // #define ENDSTOPPULLUP_YMIN // #define ENDSTOPPULLUP_ZMIN #endif #ifdef ENDSTOPPULLUPS #define ENDSTOPPULLUP_XMAX #define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_YMIN #define ENDSTOPPULLUP_ZMIN #endif // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. //#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS // Disable max endstops for compatibility with endstop checking routine #if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS) #define DISABLE_MAX_ENDSTOPS #endif // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 #define X_ENABLE_ON 0 #define Y_ENABLE_ON 0 #define Z_ENABLE_ON 0 #define E_ENABLE_ON 0 // For all extruders // Disables axis when it's not being used. #define DISABLE_X false #define DISABLE_Y false #define DISABLE_Z false #define DISABLE_E false // For all extruders #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false #define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_E0_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR -1 #define Y_HOME_DIR -1 #define Z_HOME_DIR -1 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // Travel limits after homing #define X_MAX_POS 205 #define X_MIN_POS 0 #define Y_MAX_POS 205 #define Y_MIN_POS 0 #define Z_MAX_POS 200 #define Z_MIN_POS 0 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS) #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS) #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
Re: CoreXY Stepperanschluss 29. December 2014 15:29 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 446 |
Re: CoreXY Stepperanschluss 29. December 2014 15:54 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 4.977 |
Triffid Hunter's Calibration Guide | --> X <-- Drill for new Monitor | Most important Gcode. |
Re: CoreXY Stepperanschluss 29. December 2014 16:31 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 229 |
Quote
Wurstnase
X und Y Motoren tauschen und drehen.