slicer configuration
Posted by jf pion
|
slicer configuration April 19, 2012 02:03PM |
Registered: 12 years ago Posts: 141 |
hello again
is there an manual somewhere with the explaination about all the factor you could tune in slicer ? i can't find one so I don't know what to change and what it's supposed to do
and a process of tuning a prusa could be great, how to know if the speed are correct, the temp, the extruder speed ....and so on
thank you
is there an manual somewhere with the explaination about all the factor you could tune in slicer ? i can't find one so I don't know what to change and what it's supposed to do
and a process of tuning a prusa could be great, how to know if the speed are correct, the temp, the extruder speed ....and so on
thank you
|
Re: slicer configuration April 20, 2012 01:39AM |
Registered: 12 years ago Posts: 26 |
|
Re: slicer configuration April 20, 2012 06:32AM |
Registered: 12 years ago Posts: 141 |
|
Re: slicer configuration April 20, 2012 11:16AM |
Registered: 12 years ago Posts: 1,611 |
RichRap's guide is excellent:
[richrap.blogspot.co.uk]
[richrap.blogspot.co.uk]
[richrap.blogspot.co.uk]
I'm writing some simple notes for our build group, but haven't quite finished yet: [www.tvrrug.org.uk]
[richrap.blogspot.co.uk]
[richrap.blogspot.co.uk]
[richrap.blogspot.co.uk]
I'm writing some simple notes for our build group, but haven't quite finished yet: [www.tvrrug.org.uk]
|
Re: slicer configuration July 03, 2012 09:08PM |
Registered: 11 years ago Posts: 4 |
Francois Wrote:
-------------------------------------------------------
> There is no manual per say, AFAIK.
> Have you seen these pages ?
I don't understand why there would'nt be a manual or at least a section with all the settings and explinations of what they are, defaults, and what happens when you change the settings. It would sure help all of us that are new to the program. Plus there have been a few new versions lately with new settings. Those pages are helpful but it would be nice to have a section like this with everything in one place.
-------------------------------------------------------
> There is no manual per say, AFAIK.
> Have you seen these pages ?
I don't understand why there would'nt be a manual or at least a section with all the settings and explinations of what they are, defaults, and what happens when you change the settings. It would sure help all of us that are new to the program. Plus there have been a few new versions lately with new settings. Those pages are helpful but it would be nice to have a section like this with everything in one place.
|
Re: slicer configuration July 04, 2012 04:25AM |
Admin Registered: 12 years ago Posts: 2,569 |
mikemwa Wrote:
-------------------------------------------------------
> I don't understand why there would'nt be a manual
> or at least a section with all the settings and
> explinations of what they are, defaults, and what
> happens when you change the settings.
The reason why is simple : nobody made it.
> It would sure help all of us that are new to the program.
> Plus there have been a few new versions lately
> with new settings. Those pages are helpful but it
> would be nice to have a section like this with
> everything in one place.
Feel free to write one (once you get used to Slic3r a bit) and send it to Sound for inclusion somewhere appropriate.
Most of my technical comments should be correct, but is THIS one ?
Anyway, as a rule of thumb, always double check what people write.
-------------------------------------------------------
> I don't understand why there would'nt be a manual
> or at least a section with all the settings and
> explinations of what they are, defaults, and what
> happens when you change the settings.
The reason why is simple : nobody made it.
> It would sure help all of us that are new to the program.
> Plus there have been a few new versions lately
> with new settings. Those pages are helpful but it
> would be nice to have a section like this with
> everything in one place.
Feel free to write one (once you get used to Slic3r a bit) and send it to Sound for inclusion somewhere appropriate.
Most of my technical comments should be correct, but is THIS one ?
Anyway, as a rule of thumb, always double check what people write.
Sorry, only registered users may post in this forum.