Slic3r 0.9.2

Hi,

Just downloaded 092 version and I think there is a bug.
When starting first layer it appears as the lift value is added to the layer height.
In my case I use 0.2 layer height it adds my 0.6 lift to it making layer height 0.8.
Anyone can confirm?

Regards
Jan

I haven't checked for this yet. But I have noticed that if the first layer is printed at a slower speed, say 50%, then it doesn't seem to change the extruder flow rate. Instead it increases the filament width to compensate for the slower head speed. Older versions slow down both the extruder flow rate along with the xy feed rate.

Well, maybe I am the only one experiencing this, which means it is probably not slic3r but my setup.
If I slice in 091 all good in regards to layer hight.
If I slice same file in 092 with same settings the printer starts by moving slowly to 0.0.0 then it lifts straight up what occurs to be 0.8mm and stays there during print. Unusable.
If I change my lift setting to 0 it does not do this behavior, but prints ok.
Strange.

Regards
Jan

Have you tried backing up your settings then blowing them away and re-entering them from scratch?

I've seen mention of a few cases of this needing to be done after upgrades to Slic3r in the past.

Have you looked at the g-code? Since I don't use the lift feature, I haven't encountered this myself.

I'll blow all settings away and try.

with default settings and 0.6 lift:

; generated by Slic3r 0.9.2 on 2012-09-01 at 23:49:21

; layer_height = 0.4
; perimeters = 3
; solid_layers = 3
; fill_density = 0.4
; perimeter_speed = 30
; infill_speed = 60
; travel_speed = 130
; scale = 1
; nozzle_diameter = 0.5
; filament_diameter = 3
; extrusion_multiplier = 1
; single wall width = 0.53mm
; first layer single wall width = 0.80mm

M104 S200 ; set temperature
G28 ; home all axes
M109 S200 ; wait for temperature to be reached
G90 ; use absolute coordinates
G21 ; set units to millimeters
G92 E0
M82 ; use absolute distances for extrusion
G1 X90.520 Y90.710
G1 Z0.000 // I would have expected this to be 0.4
G1 F1800.000 E1.00000
G1 X90.910 Y90.330 F540.000 E1.02267
G1 X91.330 Y89.990 E1.04516
G1 X91.780 Y89.680 E1.06791
G1 X92.250 Y89.410 E1.09047
G1 X92.750 Y89.170 E1.11356
G1 X93.260 Y88.980 E1.13621
G1 X93.780 Y88.830 E1.15874
G1 X94.310 Y88.720 E1.18128
G1 X94.860 Y88.650 E1.20436
G1 X95.400 Y88.630 E1.22685
G1 X105.130 Y88.650 E1.63189
G1 X105.680 Y88.720 E1.65497
G1 X106.210 Y88.830 E1.67750
G1 X106.730 Y88.980 E1.70003
G1 X107.240 Y89.170 E1.72268
G1 X107.740 Y89.410 E1.74577
G1 X108.210 Y89.680 E1.76834
G1 X108.660 Y89.990 E1.79108
G1 X109.080 Y90.330 E1.81358
G1 X109.660 Y90.910 E1.84772
G1 X110.000 Y91.330 E1.87022
G1 X110.310 Y91.780 E1.89296
G1 X110.580 Y92.250 E1.91553
G1 X110.820 Y92.750 E1.93861
G1 X111.010 Y93.260 E1.96127
G1 X111.160 Y93.780 E1.98380
G1 X111.270 Y94.310 E2.00633
G1 X111.340 Y94.860 E2.02941
G1 X111.340 Y105.130 E2.45693
G1 X111.270 Y105.680 E2.48001
G1 X111.160 Y106.210 E2.50254
G1 X111.010 Y106.730 E2.52507
G1 X110.820 Y107.240 E2.54772
G1 X110.580 Y107.740 E2.57081
G1 X110.310 Y108.210 E2.59337
G1 X110.000 Y108.660 E2.61612
G1 X109.660 Y109.080 E2.63861
G1 X109.080 Y109.660 E2.67276
G1 X108.660 Y110.000 E2.69525
G1 X108.210 Y110.310 E2.71800
G1 X107.740 Y110.580 E2.74056
G1 X107.240 Y110.820 E2.76365
G1 X106.730 Y111.010 E2.78631
G1 X106.210 Y111.160 E2.80884
G1 X105.680 Y111.270 E2.83137
G1 X105.130 Y111.340 E2.85445
G1 X104.590 Y111.360 E2.87694
G1 X94.860 Y111.340 E3.28198
G1 X94.310 Y111.270 E3.30506
G1 X93.780 Y111.160 E3.32759
G1 X93.260 Y111.010 E3.35012
G1 X92.750 Y110.820 E3.37278
G1 X92.250 Y110.580 E3.39586
G1 X91.780 Y110.310 E3.41843
G1 X91.330 Y110.000 E3.44117
G1 X90.910 Y109.660 E3.46367
G1 X90.330 Y109.080 E3.49781
G1 X89.990 Y108.660 E3.52031
G1 X89.680 Y108.210 E3.54306
G1 X89.410 Y107.740 E3.56562
G1 X89.170 Y107.240 E3.58871
G1 X88.980 Y106.730 E3.61136
G1 X88.830 Y106.210 E3.63389
G1 X88.720 Y105.680 E3.65642
G1 X88.650 Y105.130 E3.67950
G1 X88.650 Y94.860 E4.10702
G1 X88.720 Y94.310 E4.13010
G1 X88.830 Y93.780 E4.15263
G1 X88.980 Y93.260 E4.17516
G1 X89.170 Y92.750 E4.19781
G1 X89.410 Y92.250 E4.22090
G1 X89.680 Y91.780 E4.24347
G1 X89.990 Y91.330 E4.26621
G1 X90.330 Y90.910 E4.28871
G1 X90.437 Y90.797 E4.29520
G1 F1800.000 E3.29520
G1 Z0.600 F7800.000 // lifting 0.6
G92 E0
G1 X96.936 Y96.936
G1 Z0.000 // back down to layer
G1 F1800.000 E1.00000
G1 X103.064 Y96.936 F540.000 E1.25513
G1 X103.064 Y103.064 E1.51025
G1 X96.936 Y103.064 E1.76538
G1 X96.936 Y97.056 E2.01551
G1 X96.168 Y96.168 F7800.000
G1 X103.832 Y96.168 F540.000 E2.33456
G1 X103.832 Y103.832 E2.65360
G1 X96.168 Y103.832 E2.97265
G1 X96.168 Y96.288 E3.28671
G1 X95.400 Y95.400 F7800.000
G1 X104.600 Y95.400 F540.000 E3.66968
G1 X104.600 Y104.600 E4.05265
G1 X95.400 Y104.600 E4.43563
G1 X95.400 Y95.520 E4.81361
G1 F1800.000 E3.81361
G1 Z0.600 F7800.000
G92 E0
G1 X102.070 Y97.477
G1 Z0.000
G1 F1800.000 E1.00000
G1 X102.523 Y97.930 F1080.000 E1.02806
G1 X102.523 Y99.078 E1.07839
G1 X100.922 Y97.477 E1.17762
G1 X99.774 Y97.477 E1.22794
G1 X102.523 Y100.226 E1.39834
G1 X102.523 Y101.375 E1.44866
G1 X98.625 Y97.477 E1.69024
G1 X97.477 Y97.477 E1.74056
G1 X102.523 Y102.523 E2.05329
G1 X101.375 Y102.523 E2.10361
G1 X97.477 Y98.625 E2.34518
G1 X97.477 Y99.774 E2.39550
G1 X100.226 Y102.523 E2.56590
G1 X99.078 Y102.523 E2.61623
G1 X97.477 Y100.922 E2.71546
G1 X97.477 Y102.070 E2.76579
G1 X97.930 Y102.523 E2.79385
G1 F1800.000 E1.79385
G1 Z1.400 F7800.000 // okey, it is now lifting 0.6 and going up 1 layer of 0.4 but also it thinks that first layer was 0.4 which it should have been, but it actually was 0 so it adds another 0.4
G92 E0
G1 X96.307 Y103.693
G1 Z0.800 // so we now have a second layer of 0.8 which is correct provided first layer had been 0.4 not 0
G1 F1800.000 E1.00000
G1 X96.307 Y96.307 F1800.000 E1.21718
G1 X103.693 Y96.307 E1.43436
G1 X103.693 Y103.693 E1.65154
G1 X96.386 Y103.693 E1.86640
G1 X95.785 Y104.215 F7800.000
G1 X95.785 Y95.785 F1800.000 E2.11430
G1 X104.215 Y95.785 E2.36220
G1 X104.215 Y104.215 E2.61010
G1 X95.864 Y104.215 E2.85568
G1 X95.263 Y104.738 F7800.000
G1 X95.263 Y95.263 F1800.000 E3.13429
G1 X104.738 Y95.263 E3.41291
G1 X104.738 Y104.738 E3.69152
G1 X95.341 Y104.738 E3.96782
G1 F1800.000 E2.96782
G1 Z1.400 F7800.000 //lifting 0.6
G92 E0
G1 X103.319 Y103.022
G1 Z0.800 // going back down 0.6
G1 F1800.000 E1.00000
G1 X103.022 Y103.319 F3600.000 E1.01246
G1 X102.276 Y103.319 E1.03460
G1 X103.319 Y102.276 E1.07836
G1 X103.319 Y101.530 E1.10049
G1 X101.530 Y103.319 E1.17555
G1 X100.784 Y103.319 E1.19768
G1 X103.319 Y100.784 E1.30404
G1 X103.319 Y100.038 E1.32617
G1 X100.038 Y103.319 E1.46382
G1 X99.292 Y103.319 E1.48595
G1 X103.319 Y99.292 E1.65490
G1 X103.319 Y98.546 E1.67703
G1 X98.546 Y103.319 E1.87728
G1 X97.800 Y103.319 E1.89941
G1 X103.319 Y97.800 E2.13094
G1 X103.319 Y97.054 E2.15307
G1 X97.054 Y103.319 E2.41591
G1 X96.681 Y102.946 E2.43156
G1 X102.946 Y96.681 E2.69439
G1 X102.200 Y96.681 E2.71652
G1 X96.681 Y102.200 E2.94806
G1 X96.681 Y101.454 E2.97020
G1 X101.454 Y96.681 E3.17044
G1 X100.708 Y96.681 E3.19257
G1 X96.681 Y100.708 E3.36152
G1 X96.681 Y99.962 E3.38365
G1 X99.962 Y96.681 E3.52130
G1 X99.216 Y96.681 E3.54343
G1 X96.681 Y99.216 E3.64979
G1 X96.681 Y98.470 E3.67191
G1 X98.470 Y96.681 E3.74698
G1 X97.724 Y96.681 E3.76911
G1 X96.681 Y97.724 E3.81287
G1 X96.681 Y96.978 E3.83500
G1 X96.978 Y96.681 E3.84746
G1 F1800.000 E2.84746
G1 Z1.800 F7800.000 // going up to next layer which is 1.2 and lifting 0.6
G92 E0
G1 X96.307 Y96.307
G1 Z1.200 // back down 0.6
G1 F1800.000 E1.00000
G1 X103.693 Y96.307 F1800.000 E1.21718
G1 X103.693 Y103.693 E1.43436
G1 X96.307 Y103.693 E1.65154
G1 X96.307 Y96.386 E1.86640
G1 X95.785 Y95.785 F7800.000
G1 X104.215 Y95.785 F1800.000 E2.11430
G1 X104.215 Y104.215 E2.36220
G1 X95.785 Y104.215 E2.61010
G1 X95.785 Y95.864 E2.85568
G1 X95.263 Y95.263 F7800.000
G1 X104.738 Y95.263 F1800.000 E3.13429
G1 X104.738 Y104.738 E3.41291
G1 X95.263 Y104.738 E3.69152
G1 X95.263 Y95.341 E3.96782
G1 F1800.000 E2.96782
G1 Z1.800 F7800.000 // lifting 0.6
G92 E0
G1 X96.978 Y103.319
G1 Z1.200 // back down 0.6
G1 F1800.000 E1.00000
G1 X96.681 Y103.022 F3600.000 E1.01247
G1 X96.681 Y102.276 E1.03460
G1 X97.724 Y103.319 E1.07836
G1 X98.470 Y103.319 E1.10049
G1 X96.681 Y101.530 E1.17555
G1 X96.681 Y100.784 E1.19768
G1 X99.216 Y103.319 E1.30404
G1 X99.962 Y103.319 E1.32617
G1 X96.681 Y100.038 E1.46382
G1 X96.681 Y99.292 E1.48595
G1 X100.708 Y103.319 E1.65490
G1 X101.454 Y103.319 E1.67703
G1 X96.681 Y98.546 E1.87728
G1 X96.681 Y97.800 E1.89941
G1 X102.200 Y103.319 E2.13095
G1 X102.946 Y103.319 E2.15308
G1 X96.681 Y97.054 E2.41592
G1 X97.054 Y96.681 E2.43157
G1 X103.319 Y102.946 E2.69441
G1 X103.319 Y102.200 E2.71654
G1 X97.800 Y96.681 E2.94808
G1 X98.546 Y96.681 E2.97021
G1 X103.319 Y101.454 E3.17045
G1 X103.319 Y100.708 E3.19258
G1 X99.292 Y96.681 E3.36153
G1 X100.038 Y96.681 E3.38366
G1 X103.319 Y99.962 E3.52131
G1 X103.319 Y99.216 E3.54344
G1 X100.784 Y96.681 E3.64980
G1 X101.530 Y96.681 E3.67192
G1 X103.319 Y98.470 E3.74698
G1 X103.319 Y97.724 E3.76911
G1 X102.276 Y96.681 E3.81288
G1 X103.022 Y96.681 E3.83501
G1 X103.319 Y96.978 E3.84748
G1 F1800.000 E2.84748
G1 Z2.200 F7800.000 // going up to next layer which is 1.6 and lifting 0.6
G92 E0
G1 X103.693 Y96.307
G1 Z1.600 // down to layer
G1 F1800.000 E1.00000
G1 X103.693 Y103.693 F1800.000 E1.21718
G1 X96.307 Y103.693 E1.43436
G1 X96.307 Y96.307 E1.65154
G1 X103.614 Y96.307 E1.86640
G1 X104.215 Y95.785 F7800.000
G1 X104.215 Y104.215 F1800.000 E2.11430
G1 X95.785 Y104.215 E2.36220
G1 X95.785 Y95.785 E2.61010
G1 X104.136 Y95.785 E2.85568
G1 X104.738 Y95.263 F7800.000
G1 X104.738 Y104.738 F1800.000 E3.13429
G1 X95.263 Y104.738 E3.41291
G1 X95.263 Y95.263 E3.69152
G1 X104.659 Y95.263 E3.96782
G1 F1800.000 E2.96782
G1 Z2.200 F7800.000 // going up 0.6
G92 E0
G1 X96.978 Y96.681
G1 Z1.600 // and down 0.6
G1 F1800.000 E1.00000
G1 X96.681 Y96.978 F3600.000 E1.01246
G1 X96.681 Y97.724 E1.03459
G1 X97.724 Y96.681 E1.07835
G1 X98.470 Y96.681 E1.10049
G1 X96.681 Y98.470 E1.17555
G1 X96.681 Y99.216 E1.19768
G1 X99.216 Y96.681 E1.30403
G1 X99.962 Y96.681 E1.32616
G1 X96.681 Y99.962 E1.46382
G1 X96.681 Y100.708 E1.48595
G1 X100.708 Y96.681 E1.65489
G1 X101.454 Y96.681 E1.67702
G1 X96.681 Y101.454 E1.87727
G1 X96.681 Y102.200 E1.89940
G1 X102.200 Y96.681 E2.13094
G1 X102.946 Y96.681 E2.15307
G1 X96.681 Y102.946 E2.41590
G1 X97.054 Y103.319 E2.43155
G1 X103.319 Y97.054 E2.69439
G1 X103.319 Y97.800 E2.71652
G1 X97.800 Y103.319 E2.94806
G1 X98.546 Y103.319 E2.97019
G1 X103.319 Y98.546 E3.17043
G1 X103.319 Y99.292 E3.19256
G1 X99.292 Y103.319 E3.36151
G1 X100.038 Y103.319 E3.38364
G1 X103.319 Y100.038 E3.52129
G1 X103.319 Y100.784 E3.54342
G1 X100.784 Y103.319 E3.64978
G1 X101.530 Y103.319 E3.67191
G1 X103.319 Y101.530 E3.74697
G1 X103.319 Y102.276 E3.76910
G1 X102.276 Y103.319 E3.81287
G1 X103.022 Y103.319 E3.83500
G1 X103.319 Y103.022 E3.84746
G1 F1800.000 E2.84746
G1 Z2.600 F7800.000 // // going up to next layer which is 2.0 and lifting 0.6
G92 E0
G1 X103.693 Y103.693
G1 Z2.000 // down 0.6 to layer
G1 F1800.000 E1.00000
G1 X96.307 Y103.693 F1800.000 E1.21718
G1 X96.307 Y96.307 E1.43436
G1 X103.693 Y96.307 E1.65154
G1 X103.693 Y103.614 E1.86640
G1 X104.215 Y104.215 F7800.000
G1 X95.785 Y104.215 F1800.000 E2.11430
G1 X95.785 Y95.785 E2.36220
G1 X104.215 Y95.785 E2.61010
G1 X104.215 Y104.136 E2.85568
G1 X104.738 Y104.738 F7800.000
G1 X95.263 Y104.738 F1800.000 E3.13429
G1 X95.263 Y95.263 E3.41291
G1 X104.738 Y95.263 E3.69152
G1 X104.738 Y104.659 E3.96782
G1 F1800.000 E2.96782
G1 Z2.600 F7800.000 // lift 0.6
G92 E0
G1 X103.319 Y96.978
G1 Z2.000 // down 0.6
G1 F1800.000 E1.00000
G1 X103.022 Y96.681 F3000.000 E1.01247
G1 X102.276 Y96.681 E1.03460
G1 X103.319 Y97.724 E1.07836
G1 X103.319 Y98.470 E1.10049
G1 X101.530 Y96.681 E1.17555
G1 X100.784 Y96.681 E1.19768
G1 X103.319 Y99.216 E1.30403
G1 X103.319 Y99.962 E1.32616
G1 X100.038 Y96.681 E1.46381
G1 X99.292 Y96.681 E1.48594
G1 X103.319 Y100.708 E1.65489
G1 X103.319 Y101.454 E1.67702
G1 X98.546 Y96.681 E1.87726
G1 X97.800 Y96.681 E1.89939
G1 X103.319 Y102.200 E2.13093
G1 X103.319 Y102.946 E2.15306
G1 X97.054 Y96.681 E2.41590
G1 X96.681 Y97.054 E2.43155
G1 X102.946 Y103.319 E2.69439
G1 X102.200 Y103.319 E2.71652
G1 X96.681 Y97.800 E2.94806
G1 X96.681 Y98.546 E2.97019
G1 X101.454 Y103.319 E3.17043
G1 X100.708 Y103.319 E3.19256
G1 X96.681 Y99.292 E3.36151
G1 X96.681 Y100.038 E3.38364
G1 X99.962 Y103.319 E3.52129
G1 X99.216 Y103.319 E3.54342
G1 X96.681 Y100.784 E3.64977
G1 X96.681 Y101.530 E3.67190
G1 X98.470 Y103.319 E3.74696
G1 X97.724 Y103.319 E3.76909
G1 X96.681 Y102.276 E3.81285
G1 X96.681 Y103.022 E3.83498
G1 X96.978 Y103.319 E3.84745
G1 F1800.000 E2.84745
G1 Z2.600 F7800.000 // lift 0.6 and job done
G92 E0
M104 S0 ; turn off temperature
G28 X0 ; home X axis
M84 ; disable motors

; filament used = 32.2mm (0.2cm3)


with default settings and 0 lift:

; generated by Slic3r 0.9.2 on 2012-09-01 at 23:54:06

; layer_height = 0.4
; perimeters = 3
; solid_layers = 3
; fill_density = 0.4
; perimeter_speed = 30
; infill_speed = 60
; travel_speed = 130
; scale = 1
; nozzle_diameter = 0.5
; filament_diameter = 3
; extrusion_multiplier = 1
; single wall width = 0.53mm
; first layer single wall width = 0.80mm

M104 S200 ; set temperature
G28 ; home all axes
M109 S200 ; wait for temperature to be reached
G90 ; use absolute coordinates
G21 ; set units to millimeters
G92 E0
M82 ; use absolute distances for extrusion
G1 Z0.400 F7800.000 // first layer is correct at 0.4
G1 X90.520 Y90.710
G1 F1800.000 E1.00000
G1 X90.910 Y90.330 F540.000 E1.02267
G1 X91.330 Y89.990 E1.04516
G1 X91.780 Y89.680 E1.06791
G1 X92.250 Y89.410 E1.09047
G1 X92.750 Y89.170 E1.11356
G1 X93.260 Y88.980 E1.13621
G1 X93.780 Y88.830 E1.15874
G1 X94.310 Y88.720 E1.18128
G1 X94.860 Y88.650 E1.20436
G1 X95.400 Y88.630 E1.22685
G1 X105.130 Y88.650 E1.63189
G1 X105.680 Y88.720 E1.65497
G1 X106.210 Y88.830 E1.67750
G1 X106.730 Y88.980 E1.70003
G1 X107.240 Y89.170 E1.72268
G1 X107.740 Y89.410 E1.74577
G1 X108.210 Y89.680 E1.76834
G1 X108.660 Y89.990 E1.79108
G1 X109.080 Y90.330 E1.81358
G1 X109.660 Y90.910 E1.84772
G1 X110.000 Y91.330 E1.87022
G1 X110.310 Y91.780 E1.89296
G1 X110.580 Y92.250 E1.91553
G1 X110.820 Y92.750 E1.93861
G1 X111.010 Y93.260 E1.96127
G1 X111.160 Y93.780 E1.98380
G1 X111.270 Y94.310 E2.00633
G1 X111.340 Y94.860 E2.02941
G1 X111.340 Y105.130 E2.45693
G1 X111.270 Y105.680 E2.48001
G1 X111.160 Y106.210 E2.50254
G1 X111.010 Y106.730 E2.52507
G1 X110.820 Y107.240 E2.54772
G1 X110.580 Y107.740 E2.57081
G1 X110.310 Y108.210 E2.59337
G1 X110.000 Y108.660 E2.61612
G1 X109.660 Y109.080 E2.63861
G1 X109.080 Y109.660 E2.67276
G1 X108.660 Y110.000 E2.69525
G1 X108.210 Y110.310 E2.71800
G1 X107.740 Y110.580 E2.74056
G1 X107.240 Y110.820 E2.76365
G1 X106.730 Y111.010 E2.78631
G1 X106.210 Y111.160 E2.80884
G1 X105.680 Y111.270 E2.83137
G1 X105.130 Y111.340 E2.85445
G1 X104.590 Y111.360 E2.87694
G1 X94.860 Y111.340 E3.28198
G1 X94.310 Y111.270 E3.30506
G1 X93.780 Y111.160 E3.32759
G1 X93.260 Y111.010 E3.35012
G1 X92.750 Y110.820 E3.37278
G1 X92.250 Y110.580 E3.39586
G1 X91.780 Y110.310 E3.41843
G1 X91.330 Y110.000 E3.44117
G1 X90.910 Y109.660 E3.46367
G1 X90.330 Y109.080 E3.49781
G1 X89.990 Y108.660 E3.52031
G1 X89.680 Y108.210 E3.54306
G1 X89.410 Y107.740 E3.56562
G1 X89.170 Y107.240 E3.58871
G1 X88.980 Y106.730 E3.61136
G1 X88.830 Y106.210 E3.63389
G1 X88.720 Y105.680 E3.65642
G1 X88.650 Y105.130 E3.67950
G1 X88.650 Y94.860 E4.10702
G1 X88.720 Y94.310 E4.13010
G1 X88.830 Y93.780 E4.15263
G1 X88.980 Y93.260 E4.17516
G1 X89.170 Y92.750 E4.19781
G1 X89.410 Y92.250 E4.22090
G1 X89.680 Y91.780 E4.24347
G1 X89.990 Y91.330 E4.26621
G1 X90.330 Y90.910 E4.28871
G1 X90.437 Y90.797 E4.29520
G1 F1800.000 E3.29520
G92 E0
G1 X96.936 Y96.936 F7800.000
G1 F1800.000 E1.00000
G1 X103.064 Y96.936 F540.000 E1.25513
G1 X103.064 Y103.064 E1.51025
G1 X96.936 Y103.064 E1.76538
G1 X96.936 Y97.056 E2.01551
G1 X96.168 Y96.168 F7800.000
G1 X103.832 Y96.168 F540.000 E2.33456
G1 X103.832 Y103.832 E2.65360
G1 X96.168 Y103.832 E2.97265
G1 X96.168 Y96.288 E3.28671
G1 X95.400 Y95.400 F7800.000
G1 X104.600 Y95.400 F540.000 E3.66968
G1 X104.600 Y104.600 E4.05265
G1 X95.400 Y104.600 E4.43563
G1 X95.400 Y95.520 E4.81361
G1 F1800.000 E3.81361
G92 E0
G1 X102.070 Y97.477 F7800.000
G1 F1800.000 E1.00000
G1 X102.523 Y97.930 F1080.000 E1.02806
G1 X102.523 Y99.078 E1.07839
G1 X100.922 Y97.477 E1.17762
G1 X99.774 Y97.477 E1.22794
G1 X102.523 Y100.226 E1.39834
G1 X102.523 Y101.375 E1.44866
G1 X98.625 Y97.477 E1.69024
G1 X97.477 Y97.477 E1.74056
G1 X102.523 Y102.523 E2.05329
G1 X101.375 Y102.523 E2.10361
G1 X97.477 Y98.625 E2.34518
G1 X97.477 Y99.774 E2.39550
G1 X100.226 Y102.523 E2.56590
G1 X99.078 Y102.523 E2.61623
G1 X97.477 Y100.922 E2.71546
G1 X97.477 Y102.070 E2.76579
G1 X97.930 Y102.523 E2.79385
G1 F1800.000 E1.79385
G92 E0
G1 Z0.800 F7800.000 // second layer is correct at 0.8
G1 X96.307 Y103.693
G1 F1800.000 E1.00000
G1 X96.307 Y96.307 F1800.000 E1.21718
G1 X103.693 Y96.307 E1.43436
G1 X103.693 Y103.693 E1.65154
G1 X96.386 Y103.693 E1.86640
G1 X95.785 Y104.215 F7800.000
G1 X95.785 Y95.785 F1800.000 E2.11430
G1 X104.215 Y95.785 E2.36220
G1 X104.215 Y104.215 E2.61010
G1 X95.864 Y104.215 E2.85568
G1 X95.263 Y104.738 F7800.000
G1 X95.263 Y95.263 F1800.000 E3.13429
G1 X104.738 Y95.263 E3.41291
G1 X104.738 Y104.738 E3.69152
G1 X95.341 Y104.738 E3.96782
G1 F1800.000 E2.96782
G92 E0
G1 X103.319 Y103.022 F7800.000
G1 F1800.000 E1.00000
G1 X103.022 Y103.319 F3600.000 E1.01246
G1 X102.276 Y103.319 E1.03460
G1 X103.319 Y102.276 E1.07836
G1 X103.319 Y101.530 E1.10049
G1 X101.530 Y103.319 E1.17555
G1 X100.784 Y103.319 E1.19768
G1 X103.319 Y100.784 E1.30404
G1 X103.319 Y100.038 E1.32617
G1 X100.038 Y103.319 E1.46382
G1 X99.292 Y103.319 E1.48595
G1 X103.319 Y99.292 E1.65490
G1 X103.319 Y98.546 E1.67703
G1 X98.546 Y103.319 E1.87728
G1 X97.800 Y103.319 E1.89941
G1 X103.319 Y97.800 E2.13094
G1 X103.319 Y97.054 E2.15307
G1 X97.054 Y103.319 E2.41591
G1 X96.681 Y102.946 E2.43156
G1 X102.946 Y96.681 E2.69439
G1 X102.200 Y96.681 E2.71652
G1 X96.681 Y102.200 E2.94806
G1 X96.681 Y101.454 E2.97020
G1 X101.454 Y96.681 E3.17044
G1 X100.708 Y96.681 E3.19257
G1 X96.681 Y100.708 E3.36152
G1 X96.681 Y99.962 E3.38365
G1 X99.962 Y96.681 E3.52130
G1 X99.216 Y96.681 E3.54343
G1 X96.681 Y99.216 E3.64979
G1 X96.681 Y98.470 E3.67191
G1 X98.470 Y96.681 E3.74698
G1 X97.724 Y96.681 E3.76911
G1 X96.681 Y97.724 E3.81287
G1 X96.681 Y96.978 E3.83500
G1 X96.978 Y96.681 E3.84746
G1 F1800.000 E2.84746
G92 E0
G1 Z1.200 F7800.000 // third layer is correct at 1.2
G1 X96.307 Y96.307
G1 F1800.000 E1.00000
G1 X103.693 Y96.307 F1800.000 E1.21718
G1 X103.693 Y103.693 E1.43436
G1 X96.307 Y103.693 E1.65154
G1 X96.307 Y96.386 E1.86640
G1 X95.785 Y95.785 F7800.000
G1 X104.215 Y95.785 F1800.000 E2.11430
G1 X104.215 Y104.215 E2.36220
G1 X95.785 Y104.215 E2.61010
G1 X95.785 Y95.864 E2.85568
G1 X95.263 Y95.263 F7800.000
G1 X104.738 Y95.263 F1800.000 E3.13429
G1 X104.738 Y104.738 E3.41291
G1 X95.263 Y104.738 E3.69152
G1 X95.263 Y95.341 E3.96782
G1 F1800.000 E2.96782
G92 E0
G1 X96.978 Y103.319 F7800.000
G1 F1800.000 E1.00000
G1 X96.681 Y103.022 F3600.000 E1.01247
G1 X96.681 Y102.276 E1.03460
G1 X97.724 Y103.319 E1.07836
G1 X98.470 Y103.319 E1.10049
G1 X96.681 Y101.530 E1.17555
G1 X96.681 Y100.784 E1.19768
G1 X99.216 Y103.319 E1.30404
G1 X99.962 Y103.319 E1.32617
G1 X96.681 Y100.038 E1.46382
G1 X96.681 Y99.292 E1.48595
G1 X100.708 Y103.319 E1.65490
G1 X101.454 Y103.319 E1.67703
G1 X96.681 Y98.546 E1.87728
G1 X96.681 Y97.800 E1.89941
G1 X102.200 Y103.319 E2.13095
G1 X102.946 Y103.319 E2.15308
G1 X96.681 Y97.054 E2.41592
G1 X97.054 Y96.681 E2.43157
G1 X103.319 Y102.946 E2.69441
G1 X103.319 Y102.200 E2.71654
G1 X97.800 Y96.681 E2.94808
G1 X98.546 Y96.681 E2.97021
G1 X103.319 Y101.454 E3.17045
G1 X103.319 Y100.708 E3.19258
G1 X99.292 Y96.681 E3.36153
G1 X100.038 Y96.681 E3.38366
G1 X103.319 Y99.962 E3.52131
G1 X103.319 Y99.216 E3.54344
G1 X100.784 Y96.681 E3.64980
G1 X101.530 Y96.681 E3.67192
G1 X103.319 Y98.470 E3.74698
G1 X103.319 Y97.724 E3.76911
G1 X102.276 Y96.681 E3.81288
G1 X103.022 Y96.681 E3.83501
G1 X103.319 Y96.978 E3.84748
G1 F1800.000 E2.84748
G92 E0
G1 Z1.600 F7800.000c // fourth layer is correct at 1.6
G1 X103.693 Y96.307
G1 F1800.000 E1.00000
G1 X103.693 Y103.693 F1800.000 E1.21718
G1 X96.307 Y103.693 E1.43436
G1 X96.307 Y96.307 E1.65154
G1 X103.614 Y96.307 E1.86640
G1 X104.215 Y95.785 F7800.000
G1 X104.215 Y104.215 F1800.000 E2.11430
G1 X95.785 Y104.215 E2.36220
G1 X95.785 Y95.785 E2.61010
G1 X104.136 Y95.785 E2.85568
G1 X104.738 Y95.263 F7800.000
G1 X104.738 Y104.738 F1800.000 E3.13429
G1 X95.263 Y104.738 E3.41291
G1 X95.263 Y95.263 E3.69152
G1 X104.659 Y95.263 E3.96782
G1 F1800.000 E2.96782
G92 E0
G1 X96.978 Y96.681 F7800.000
G1 F1800.000 E1.00000
G1 X96.681 Y96.978 F3600.000 E1.01246
G1 X96.681 Y97.724 E1.03459
G1 X97.724 Y96.681 E1.07835
G1 X98.470 Y96.681 E1.10049
G1 X96.681 Y98.470 E1.17555
G1 X96.681 Y99.216 E1.19768
G1 X99.216 Y96.681 E1.30403
G1 X99.962 Y96.681 E1.32616
G1 X96.681 Y99.962 E1.46382
G1 X96.681 Y100.708 E1.48595
G1 X100.708 Y96.681 E1.65489
G1 X101.454 Y96.681 E1.67702
G1 X96.681 Y101.454 E1.87727
G1 X96.681 Y102.200 E1.89940
G1 X102.200 Y96.681 E2.13094
G1 X102.946 Y96.681 E2.15307
G1 X96.681 Y102.946 E2.41590
G1 X97.054 Y103.319 E2.43155
G1 X103.319 Y97.054 E2.69439
G1 X103.319 Y97.800 E2.71652
G1 X97.800 Y103.319 E2.94806
G1 X98.546 Y103.319 E2.97019
G1 X103.319 Y98.546 E3.17043
G1 X103.319 Y99.292 E3.19256
G1 X99.292 Y103.319 E3.36151
G1 X100.038 Y103.319 E3.38364
G1 X103.319 Y100.038 E3.52129
G1 X103.319 Y100.784 E3.54342
G1 X100.784 Y103.319 E3.64978
G1 X101.530 Y103.319 E3.67191
G1 X103.319 Y101.530 E3.74697
G1 X103.319 Y102.276 E3.76910
G1 X102.276 Y103.319 E3.81287
G1 X103.022 Y103.319 E3.83500
G1 X103.319 Y103.022 E3.84746
G1 F1800.000 E2.84746
G92 E0
G1 Z2.000 F7800.000 // fifth layer is correct at 2.0
G1 X103.693 Y103.693
G1 F1800.000 E1.00000
G1 X96.307 Y103.693 F1800.000 E1.21718
G1 X96.307 Y96.307 E1.43436
G1 X103.693 Y96.307 E1.65154
G1 X103.693 Y103.614 E1.86640
G1 X104.215 Y104.215 F7800.000
G1 X95.785 Y104.215 F1800.000 E2.11430
G1 X95.785 Y95.785 E2.36220
G1 X104.215 Y95.785 E2.61010
G1 X104.215 Y104.136 E2.85568
G1 X104.738 Y104.738 F7800.000
G1 X95.263 Y104.738 F1800.000 E3.13429
G1 X95.263 Y95.263 E3.41291
G1 X104.738 Y95.263 E3.69152
G1 X104.738 Y104.659 E3.96782
G1 F1800.000 E2.96782
G92 E0
G1 X103.319 Y96.978 F7800.000
G1 F1800.000 E1.00000
G1 X103.022 Y96.681 F3000.000 E1.01247
G1 X102.276 Y96.681 E1.03460
G1 X103.319 Y97.724 E1.07836
G1 X103.319 Y98.470 E1.10049
G1 X101.530 Y96.681 E1.17555
G1 X100.784 Y96.681 E1.19768
G1 X103.319 Y99.216 E1.30403
G1 X103.319 Y99.962 E1.32616
G1 X100.038 Y96.681 E1.46381
G1 X99.292 Y96.681 E1.48594
G1 X103.319 Y100.708 E1.65489
G1 X103.319 Y101.454 E1.67702
G1 X98.546 Y96.681 E1.87726
G1 X97.800 Y96.681 E1.89939
G1 X103.319 Y102.200 E2.13093
G1 X103.319 Y102.946 E2.15306
G1 X97.054 Y96.681 E2.41590
G1 X96.681 Y97.054 E2.43155
G1 X102.946 Y103.319 E2.69439
G1 X102.200 Y103.319 E2.71652
G1 X96.681 Y97.800 E2.94806
G1 X96.681 Y98.546 E2.97019
G1 X101.454 Y103.319 E3.17043
G1 X100.708 Y103.319 E3.19256
G1 X96.681 Y99.292 E3.36151
G1 X96.681 Y100.038 E3.38364
G1 X99.962 Y103.319 E3.52129
G1 X99.216 Y103.319 E3.54342
G1 X96.681 Y100.784 E3.64977
G1 X96.681 Y101.530 E3.67190
G1 X98.470 Y103.319 E3.74696
G1 X97.724 Y103.319 E3.76909
G1 X96.681 Y102.276 E3.81285
G1 X96.681 Y103.022 E3.83498
G1 X96.978 Y103.319 E3.84745
G1 F1800.000 E2.84745
G92 E0
M104 S0 ; turn off temperature
G28 X0 ; home X axis
M84 ; disable motors

; filament used = 32.2mm (0.2cm3)

As far as I can see, when using lift something goes wrong with the first layer.
Am I right?

Regards
Jan

Edited 2 time(s). Last edit at 09/01/2012 10:47AM by IceMan.

You should report it on github Sound only frequents here intermittently.

IceMan: Definitely looks like an issue. As Polygonhell says, report it on github and hopefully Sound will address the issue soon.

It looks like it already has been reported by others. Problem with first layer if using lift and also if not using lift first layer is set to 0.

Regards
Jan

In the link you will find the guide written by me and Lorenzo Cantini of Kent’s strapper for Slic3r.

[www.ivanbortolin.it]