Need recompiled version with bigger limits
Posted by dc42
|
Need recompiled version with bigger limits January 05, 2015 06:27AM |
Registered: 11 years ago Posts: 14,686 |
OpenScad 2014.03 keeps crashing when I hit F5. Prior to crashing, it reports that it is aborting normalisation because it has reach its limit of 4000 elements. Does anyone have a Windows build of OpenScad with this limit increased?
The model compiles OK (but slowly) when I hit F6, and it compiles with F5 if I remove enough elements. It can be found at [www.thingiverse.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
The model compiles OK (but slowly) when I hit F6, and it compiles with F5 if I remove enough elements. It can be found at [www.thingiverse.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
|
Re: Need recompiled version with bigger limits January 05, 2015 08:53AM |
Registered: 11 years ago Posts: 2,472 |
I wonder why a compile doesn't work while a compile & render does?
Is there any downside to using F6? I just tried your design and while F5 gave the same error message as you describe, it rendered OK with F6 in under 2 minutes (1'46") - I've had designs that took a lot longer than that.
Dave
Edited 2 time(s). Last edit at 01/05/2015 09:03AM by dmould.
Is there any downside to using F6? I just tried your design and while F5 gave the same error message as you describe, it rendered OK with F6 in under 2 minutes (1'46") - I've had designs that took a lot longer than that.
Dave
Edited 2 time(s). Last edit at 01/05/2015 09:03AM by dmould.
|
Re: Need recompiled version with bigger limits January 05, 2015 04:56PM |
Registered: 10 years ago Posts: 119 |
|
Re: Need recompiled version with bigger limits January 10, 2015 04:25PM |
Registered: 11 years ago Posts: 28 |
|
Re: Need recompiled version with bigger limits January 10, 2015 06:33PM |
Registered: 11 years ago Posts: 14,686 |
I simplified the model an re-uploaded it a few days ago yo get round the limit. I just hope I don't hit it again too soon.
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
|
Re: Need recompiled version with bigger limits February 06, 2015 02:04PM |
Registered: 11 years ago Posts: 14,686 |
I've now hit the same problem with another model. I really wish there was a 64-bit Windows binary with much bigger limits.
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Sorry, only registered users may post in this forum.