Zdravím,
prosím všechny o pomoc se závadou.

Tiskárna (RebeliX X2, MB je Megatronics v3, FW je Marlin RC7) se v průběhu tisku zastavila, vyhřívání zůstalo zapnuté, pouze se přestala hýbat.
Po restartu tiskárna neraguje na příkazy G1/G28. Lze zapínat ventilátor, LED, detekuje teploty a může vyhřívat. Jakmile ale dám posun osy nebo home tak vypisuje do terminálu toto:
echo:busy: processing

Již několikrát přehrán FW, deska se chová stejně i když je vše odpojeno. USB kabel vyměněn. Už mě nic nenapadá tak vás prosím o další nápady. Více mozků na to snad přijde

Log:

18:09:38.434 : Serial com errorystem.IO.Ports.SerialErrorReceivedEventArgs
18:09:39.661 : Printer reset detected - initalizing
18:09:39.661 : start
18:09:39.661 : echo:Marlin 1.1.0-RC7
18:09:39.661 : echo: Last Updated: 2016-07-31 12:00 | Author: (RebeliX)
18:09:39.661 : Compiled: Mar 10 2017
18:09:39.662 : echo: Free Memory: 4423  PlannerBufferBytes: 1232
18:09:39.662 : echo:Hardcoded Default Settings Loaded
18:09:39.662 : echoteps per unit:
18:09:39.662 : echo:  M92 X160.00 Y160.00 Z800.00 E830.00
18:09:39.662 : echo:Maximum feedrates (mm/s):
18:09:39.662 : echo:  M203 X300.00 Y300.00 Z2.50 E25.00
18:09:39.662 : echo:Maximum Acceleration (mm/s2):
18:09:39.662 : echo:  M201 X3000 Y3000 Z100 E10000
18:09:39.662 : echo:Accelerations: P=printing, R=retract and T=travel
18:09:39.663 : echo:  M204 P3000.00 R3000.00 T3000.00
18:09:39.663 : echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
18:09:39.663 : echo:  M205 S0.00 T0.00 B20000 X5.00 Z0.40 E5.00
18:09:39.663 : echo:Home offset (mm)
18:09:39.663 : echo:  M206 X0.00 Y0.00 Z0.00
18:09:39.663 : echo:Material heatup parameters:
18:09:39.663 : echo:  M145 S0 H180 B60 F0
18:09:39.664 : echo:  M145 S1 H220 B90 F0
18:09:39.664 : echoID settings:
18:09:39.664 : echo:  M301 P13.27 I0.83 D53.16
18:09:39.664 : echo:Filament settings: Disabled
18:09:39.664 : echo:  M200 D3.00
18:09:39.664 : echo:  M200 D0
18:09:39.818 : N1 M110*34
18:09:39.818 : N2 M115*36
18:09:39.818 : N3 M105*36
18:09:39.818 : N4 M114*35
18:09:39.831 : N5 M111 S6*98
18:09:39.831 : N6 T0*60
18:09:39.831 : N7 M20*22
18:09:39.832 : N8 M80*19
18:09:39.832 : N9 M105*46
18:09:42.665 : ok
18:09:42.774 : FIRMWARE_NAME:Marlin 1.1.0-RC7 (Github) SOURCE_CODE_URL:[github.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:RebeliX X2 EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
18:09:42.775 : N10 M220 S100*80
18:09:42.775 : ok
18:09:42.775 : N11 M221 S100*80
18:09:42.776 : ok T:22.1 /0.0 B:22.5 /0.0 @:0 B@:0
18:09:42.776 : N12 M111 S6*84
18:09:42.777 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0 Y:0 Z:0
18:09:42.777 : ok
18:09:42.777 : N13 T0*8
18:09:42.868 : echoEBUG:INFO,ERRORS
18:09:42.868 : ok
18:09:42.868 : echo:Active Extruder: 0
18:09:42.868 : ok
18:09:42.868 : ok
18:09:42.868 : ok
18:09:42.869 : ok T:23.1 /0.0 B:22.5 /0.0 @:0 B@:0
18:09:42.869 : ok
18:09:42.869 : ok
18:09:42.869 : echoEBUG:INFO,ERRORS
18:09:42.869 : ok
18:09:42.869 : echo:Active Extruder: 0
18:09:42.869 : ok
18:09:42.884 : N14 M105*18
18:09:42.948 : ok T:23.1 /0.0 B:22.5 /0.0 @:0 B@:0
18:09:43.070 : N15 G28*39
18:09:45.089 : echo:busy: processing
18:09:45.949 : N16 M105*16
18:09:47.086 : echo:busy: processing
18:09:49.008 : N17 M105*17
18:09:49.083 : echo:busy: processing
18:09:51.081 : echo:busy: processing
18:09:52.067 : N18 M105*30
18:09:53.078 : echo:busy: processing
18:09:55.075 : echo:busy: processing
18:09:55.134 : N19 M105*31
18:09:57.088 : echo:busy: processing
18:09:58.191 : N20 M105*21
18:09:59.086 : echo:busy: processing
18:10:01.083 : echo:busy: processing
18:10:01.257 : N21 M105*20
18:10:03.080 : echo:busy: processing
18:10:04.318 : N22 M105*23
18:10:05.093 : echo:busy: processing
18:10:07.091 : echo:busy: processing
18:10:07.384 : N23 M105*22
18:10:09.088 : echo:busy: processing
18:10:11.085 : echo:busy: processing
18:10:13.082 : echo:busy: processing
18:10:15.096 : echo:busy: processing
18:10:17.093 : echo:busy: processing
18:10:19.090 : echo:busy: processing
18:10:21.086 : echo:busy: processing
18:10:23.083 : echo:busy: processing
18:10:25.096 : echo:busy: processing
18:10:27.094 : echo:busy: processing
18:10:29.091 : echo:busy: processing
18:10:31.087 : echo:busy: processing
18:10:33.084 : echo:busy: processing
18:10:35.082 : echo:busy: processing
18:10:37.095 : echo:busy: processing
18:10:39.092 : echo:busy: processing

.

Edited 1 time(s). Last edit at 03/10/2017 06:39PM by Nemesis94.