What bearings do I use for this? Is this the correct hotend mount for gt2?
Posted by knife-edge
|
What bearings do I use for this? Is this the correct hotend mount for gt2? September 20, 2014 09:41AM |
Registered: 10 years ago Posts: 53 |
Hi guys,
I have finally gotten all my parts printed (v0.4.9) and I had not realized that the size of bearings had changed for the x and y axis. Can anyone tell me what bearings I need for this and if the hot end mount is correct for gt2 belts? I printed the 3 plates from the file folder from github so I figured that they were not a mismatched set.
Thanks,
Knife-edge
I have finally gotten all my parts printed (v0.4.9) and I had not realized that the size of bearings had changed for the x and y axis. Can anyone tell me what bearings I need for this and if the hot end mount is correct for gt2 belts? I printed the 3 plates from the file folder from github so I figured that they were not a mismatched set.
Thanks,
Knife-edge
|
Re: What bearings do I use for this? Is this the correct hotend mount for gt2? October 20, 2014 05:24PM |
Registered: 10 years ago Posts: 125 |
Use a ruler and measure the bearing holes. If they are all the same they are for LM8UU bearings and 8mm steel rod. If the 2 verticle bearing holders in the lowest component in your picture are bigger then the horizontal bearing holders in the same part then you need LM8UU and LM6UU beariings (8mm & 6mm steel rod).
I dont see a hotend mount in the picture.
Edited 1 time(s). Last edit at 10/20/2014 05:25PM by mikefiatx19.
I dont see a hotend mount in the picture.
Edited 1 time(s). Last edit at 10/20/2014 05:25PM by mikefiatx19.
|
Re: What bearings do I use for this? Is this the correct hotend mount for gt2? October 20, 2014 05:57PM |
Registered: 10 years ago Posts: 992 |
hi knife,
This version uses 6mm rods and lm6uu . Also , it's the huxley type hotend support.
I should put more explanation and more options online , with clear infos..as we have a lot of diferent options now.. my bad .
the Smartrap project
[smartfriendz.com]
[www.thingiverse.com]
[reprap.org]
[github.com]
doc assemblage: [reprap.org]
NEW: Forum smartfriendz: [smartraptalk.smartfriendz.com]
This version uses 6mm rods and lm6uu . Also , it's the huxley type hotend support.
I should put more explanation and more options online , with clear infos..as we have a lot of diferent options now.. my bad .
the Smartrap project
[smartfriendz.com]
[www.thingiverse.com]
[reprap.org]
[github.com]
doc assemblage: [reprap.org]
NEW: Forum smartfriendz: [smartraptalk.smartfriendz.com]
|
Re: What bearings do I use for this? Is this the correct hotend mount for gt2? October 20, 2014 06:50PM |
Registered: 10 years ago Posts: 53 |
|
Re: What bearings do I use for this? Is this the correct hotend mount for gt2? October 21, 2014 05:28AM |
Registered: 10 years ago Posts: 992 |
yes knife.. the plates on thingiverse are up to date and there is a jhead lite support on them.
on github, you can find it at : stl / release / endx_jheadlite.stl , arm and attach
the Smartrap project
[smartfriendz.com]
[www.thingiverse.com]
[reprap.org]
[github.com]
doc assemblage: [reprap.org]
NEW: Forum smartfriendz: [smartraptalk.smartfriendz.com]
on github, you can find it at : stl / release / endx_jheadlite.stl , arm and attach
the Smartrap project
[smartfriendz.com]
[www.thingiverse.com]
[reprap.org]
[github.com]
doc assemblage: [reprap.org]
NEW: Forum smartfriendz: [smartraptalk.smartfriendz.com]
Sorry, only registered users may post in this forum.