Artefatti superfici verticali April 12, 2018 05:52AM |
Registered: 13 years ago Posts: 414 |
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 12, 2018 03:29PM |
Registered: 10 years ago Posts: 3,268 |
Re: Artefatti superfici verticali April 13, 2018 01:28PM |
Registered: 13 years ago Posts: 414 |
Send: M503 Recv: Config: G21 ; Units in mm Recv: Recv: Config: Steps per unit: Recv: Config: M92 X320.000 Y320.000 Z1600.000 T0 E585.000 Recv: Config: Maximum feedrates (units/s): Recv: Config: M203 X250.000 Y250.000 Z5.000 T0 E100.000 Recv: Config: Maximum Acceleration (units/s2): Recv: Config: M201 X1500 Y1500 Z20 T0 E3000 Recv: Config: Acceleration (units/s2): P V T* R Recv: Config: M204 P1500.000 V1500.000 T0 R10000.000 Recv: Config: Advanced variables: S V B X Z T* E Recv: Config: M205 S0.000 V0.000 B20000 X10.000 Y10.000 Z0.400 T0 E5.000 Recv: Config: PID settings: Recv: Config: M301 H0 P8.032323 I1.197424 D13.470207 Recv: Config: Filament settings: Disabled Recv: Config: M200 T0 D1.750 Recv: Stats: Total: 0, Finished: 0, Failed: 0 Recv: Stats: Total print time: 0s, Power on time: 15m 0s Recv: Stats: Filament used: 0Km 0m 0cm 0mm
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 13, 2018 04:36PM |
Moderator Registered: 12 years ago Posts: 1,865 |
Re: Artefatti superfici verticali April 14, 2018 02:46AM |
Registered: 13 years ago Posts: 414 |
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 14, 2018 04:34AM |
Registered: 8 years ago Posts: 36 |
Re: Artefatti superfici verticali April 15, 2018 06:29AM |
Registered: 13 years ago Posts: 414 |
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 15, 2018 08:30AM |
Registered: 13 years ago Posts: 414 |
Recv: Config: Acceleration (units/s2): P V T* R
Recv: Config: M204 P1500.000 V1500.000 T0 R10000.000
Recv: Config: Advanced variables: S V B X Z T* E
Recv: Config: M205 S0.000 V0.000 B20000 X10.000 Y10.000 Z0.400 T0 E5.000
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 16, 2018 01:16PM |
Registered: 8 years ago Posts: 36 |
Re: Artefatti superfici verticali April 17, 2018 02:13AM |
Registered: 9 years ago Posts: 762 |
Quote
ghirotre
Ciao, 10 non dovrebbe essere un valore alto. Magari prova con 8
Quote
ghirotre
C è un articolo molto bello dove stampano 6 benchy cambiando il jerk e fanno tutte le comparazioni
Re: Artefatti superfici verticali April 17, 2018 12:18PM |
Registered: 13 years ago Posts: 414 |
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5
Re: Artefatti superfici verticali April 18, 2018 05:44PM |
Registered: 8 years ago Posts: 36 |
Re: Artefatti superfici verticali April 19, 2018 12:36PM |
Registered: 13 years ago Posts: 414 |
--- Prusa i3 Steel (20x20x20) --- Prusa i3 Steel XL (30x30x30)
Motori 200 passi Motori 400 passi
Stepper drive - DRV8825 Stepper drive - DRV8825
RAMPS 1.4 RADDS 1.5
HotEnd IeC HotEnd IeC
FW MK4DUO 4.3.2 FW MK4DUO 4.3.5