MarlinKimbra please help me 4.2.0 Delta, many of my problems

yg12344

MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 12:04PM

Registered: 8 years ago
Posts: 25

MarlinKimbra please help me 4.2.0 Delta, many of my problems

Delta=arduino 2560+ramps 1.4+NEXTION HMI LCD

1、NEXTION HMI LCD in the boot does not move

400px-BT_Connection_RAMPS1.4.png

HMI.png

2、Marlinkimbra.it/ cannot be configured 4.2
3、Unable to configure 6 mechanical switches, no Z probe

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 12:48PM

Registered: 10 years ago
Posts: 6,409

Are you shure D0 and D2 is Serial 1??
[www.arduino.cc]
If you see schematic of Arduino Mega, TX 1 and RX 1 D2 and D3 are used from ramps to X-min and X-max...
You must use PH1(TXD2) and PH2(RXD2) but not on ramps only arduino mega....

I check this!!!

Point 2 i do not understand...
Point 3 6 mechanical switch for what?? 3 for max and another 3???

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 01:06PM

Registered: 8 years ago
Posts: 25

Marlinkimbra firmware configuration tool (2 edition) is unable to configure the 4.2 x firmware version.

Only Xmax, Ymax, Zmax,
Z probe can not be defined

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 01:11PM

Registered: 8 years ago
Posts: 25

LCD how to connect ramps 1.4 to ask you to help draw out

20131128120828_77958.jpg

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 01:43PM

Registered: 8 years ago
Posts: 25

NEXTION HMI LCD so take it?

20131128120828_77958.jpg

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 05:39PM

Registered: 10 years ago
Posts: 6,409

Ok z probe defined in marlinkimbra.it
For Nextion on ramps the problem is this... TX1 and RX1 are used for Zmin and Zmax pin..
Now use
Xmax pin
Xmin pin for Zmax pin
Ymax pin
Ymin pin for probe pin
Now Zmin and zmax pin free for nextion...

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 10:09PM

Registered: 8 years ago
Posts: 25

Marlinkimbra.it firmware configuration tools, configuration 4.2 × firmware has not changed

Marlinkimbra.it Configuration

1.png

2.png

3.png

5.png

6.png

7.png

I get the configuration does not change Marlinkimbra.it

1-1.png

2-1.png

3-1.png

4-1.png

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 11:41PM

Registered: 8 years ago
Posts: 25

Quote
MagoKimbra
Ok z probe defined in marlinkimbra.it
For Nextion on ramps the problem is this... TX1 and RX1 are used for Zmin and Zmax pin..
Now use
Xmax pin
Xmin pin for Zmax pin
Ymax pin
Ymin pin for probe pin

Now Zmin and zmax pin free for nextion...

The same problem

HMI.png

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 14, 2015 11:54PM

Registered: 8 years ago
Posts: 25

The same problem

1.JPG

2.JPG

What am I doing wrong?

Edited 1 time(s). Last edit at 09/14/2015 11:55PM by yg12344.

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 15, 2015 02:13AM

Registered: 10 years ago
Posts: 6,409

No... 4.2.0 have new file Configuration_overall... Only this file is written by the configurator. For nextion, today I check with my ramps ...

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 15, 2015 05:24AM

Registered: 10 years ago
Posts: 6,409

O i test on Zmin e Zmax pin.. And function...

write this in configuration_pins to the end file...

#define X_MIN_PIN                3
#define X_MAX_PIN                2
#define Y_MIN_PIN               -1
#define Y_MAX_PIN               14 // Ex Y-Min
#define Z_MIN_PIN               -1
#define Z_MAX_PIN               15 // Ex Y-Max

Now Zmin and Zmax is free for Serial1 port... Zmin is TX and connect to RX nextion, Zmax is RX and connect to TX nextion...

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 15, 2015 09:40PM

Registered: 8 years ago
Posts: 25

magokimbra I've done as you say the problem

>>>m119
SENDING:M119
echo: Reporting endstop status
x_min: TRIGGERED
x_max: NOT TRIGGERED
y_max: TRIGGERED
z_max: NOT TRIGGERED
z_probe: TRIGGERED

77.JPG

Pronterface lcd connection must only be used, if not connected to the same stuck pronterface

66.JPG

55.JPG

Unable heated nozzle

Edited 2 time(s). Last edit at 09/15/2015 11:49PM by yg12344.

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 16, 2015 01:46AM

Registered: 10 years ago
Posts: 6,409

Send me your configuration_overall and configuration_pins width attach file...

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 16, 2015 03:32AM

Registered: 8 years ago
Posts: 25

this is mineConfiguration_Overall.h pins.h Configuration_Pins.h

Edited 1 time(s). Last edit at 09/16/2015 03:34AM by yg12344.

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 16, 2015 03:36AM

Registered: 8 years ago
Posts: 25

MagoKimbra Thank you for your help

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 16, 2015 08:39AM

Registered: 8 years ago
Posts: 25

NEXTION HMI LCD，Temperature can not be set

Reply Quote

MagoKimbra

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 16, 2015 05:24PM

Registered: 10 years ago
Posts: 6,409

Try now..

For end stop. Put
X-MAX on X-MIN
Y-MAX on X-MAX
Z-MAX on Y-MIN
Z-PROBE on Y-MAX

Z-min and Z-max TX and RS serial 1

Have Nextion default baudrate or have you change??

In nextion_config you can change baudrate Nextion..
When you try rembember attach serial to nextion and reset arduino..

COMPRA ITALIANO - sostieni le nostre aziende - sostieni la nostra gente - sostieni il tuo popolo - sosterrai te stesso.
Alberto C. felice possessore di una Kossel K2
My Blog - My Thingiverse

Reply Quote

Attachments:
open | download - MarlinKimbra.zip (453.3 KB)

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 17, 2015 06:27AM

Registered: 8 years ago
Posts: 25

MagoKimbra really appreciate your help now normal, and can not control the temperature in the NEXTION HMI LCD, What is the problem?

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 17, 2015 06:42AM

Registered: 8 years ago
Posts: 25

This is my printed works, and tomorrow I will print a metal

DSC_0350.JPG

DSC_0351.JPG

DSC_0352.JPG

DSC_0353.JPG

DSC_0354.JPG

DSC_0355.JPG

Reply Quote

yg12344

Re: MarlinKimbra please help me 4.2.0 Delta, many of my problems
September 20, 2015 08:10AM

Registered: 8 years ago
Posts: 25

NEXTION HMI LCD can not set the temperature, SD card can not be read black and white

Reply Quote