Welcome! Log In Create A New Profile

Advanced

Imprimanta 3D Smartrap

Posted by ldanut 
Forum List Message List New Topic
ldanut
Imprimanta 3D Smartrap
December 04, 2014 04:46AM
Imprimanta 3D SmartRap (http://reprap.org/wiki/Smartrap_mini).

Suprafata de printare: 200mmx200mmx150mm

Material Printare: ABS sau PLA 1.75mm

Pat Incalzit: 60-110 grade Celsius

Cap de printare: JHead MKVI sau AluHotend

Electronica: Arduino Mega 2560 + RAMPS1.4 + LCD

Port-uri: USB + Card Reader

Sursa: 12V 30A.

Timp necesar de executie: 1-2 saptamani.

Imprimanta este disponibila ca si kit neasamblat sau fara pat incalizt.

Variata complet asamblata 2000 RON.

Fara pat de printare 1700 RON.

Kit neasamblat 1400 RON.

Pentru a vedea ce se poate face cu ea urmariti topicul acesta.






[www.build3dparts.com]
[www.3dhubs.com]
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 05, 2014 05:10AM
HI, so how do you wire up the endstop switches?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 05, 2014 05:21AM
I wire the edge pins on endstop switch. This is what you are asking?
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 05, 2014 09:18AM
Get thanks, ill let you know how my build gets on
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 06, 2014 07:39AM
hi, what type of fan does the hotend mount use?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 06, 2014 08:01AM
40mm 12v fan
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 06, 2014 10:16AM
Thanks do you use a mount for the ramps boards?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 07, 2014 12:58AM
I use a case since I don't want to see wires and electronics: [www.thingiverse.com]
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 07, 2014 06:43AM
Hi, im having issues with my endstops (see this post [forums.reprap.org])

Any ideas? Could i have a copy of your firmware?

Many thanks
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 07, 2014 06:43AM
Thanks
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
December 09, 2014 04:29PM
Hi, do you have a link to where you bought the fitting that connects the filament tube to the printer (not sure of the name) and the tube that you have wrapped your wires in that go to the hotend? Thanks
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 09, 2014 07:04PM
The filament tube si fixed by screwing M4 nuts to the end of teflon tube. There is no special fitting required. Wire protection is purchased locally from my a electronics store. But I think you can find also here [www.tridprinting.com]
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 17, 2014 03:46AM
Versiune kit asamblare:


Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
December 17, 2014 03:47AM
Obiecte realizate pe imprimanta:


Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
January 06, 2015 03:47AM
Variante de culori:


Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
January 31, 2015 06:56PM
Imprimanta a primit un upgrade la o sonda de probare optica a patului de printare foarte precisa si va permite autonivelarea nefiind necesara calibrarea planeitatii patului fata de cap.

[www.youtube.com]

[www.youtube.com]
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 12:42PM
What hotend do you use?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 12:44PM
Aluhotend or JHead
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 12:47PM
Thanks, where do you buy them from?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 12:48PM
JHead from hotends.com and Aluhotend from [3d-industries.myshopify.com]. I can sel you one if you want.

Edited 1 time(s). Last edit at 02/01/2015 12:49PM by ldanut.
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 12:49PM
How much for one of yours?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 12:53PM
About 45Euro + 3Euro shipping. It comes prewired with 30W heating cartrige and thermistor.
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 12:54PM
Does that work with the standard smartrap mounts?
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 01:08PM
I think the original one uses JHead Lite that has a smaller groove. I can include a set of plastics for holding the hot end, fan and Z probe microswith in this price.
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 01:19PM
Okay if you could invoice me via paypal i will pay now. jack1256@hotmail.com is my paypal
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 01:21PM
Which one do you want?
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 01:24PM
Aluhotend
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 01:50PM
I will ship it tomorow. Did you check my new optical Z probe? Its a game changer in bed leveling and first layer thickness.

Also I'm working on a assembly manual for printers I sell: [build3dparts.com]

Edited 1 time(s). Last edit at 02/01/2015 01:51PM by ldanut.
Reply Quote
jbutj
Re: Imprimanta 3D Smartrap
February 01, 2015 01:56PM
Yeah looks really good but seems quite complex
Reply Quote
ldanut
Re: Imprimanta 3D Smartrap
February 01, 2015 01:59PM
I can provide one for you assembled with everything you need. Just plug it into RAMPS and write my firmware version. Not sure how much to charge for it yet smiling smiley. It was a lot of work behind it. Make me an offer if you are interested.
Reply Quote
Page 1 of 3    Pages: 123Next
Newer Topic Older Topic
Sorry, only registered users may post in this forum.

Click here to login