Folger Tech 2020 V-Rail Upgrades June 13, 2016 12:13PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 13, 2016 12:42PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 14, 2016 08:08PM |
Registered: 8 years ago Posts: 430 |
Re: Folger Tech 2020 V-Rail Upgrades June 14, 2016 10:55PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 14, 2016 11:06PM |
Registered: 8 years ago Posts: 430 |
Re: Folger Tech 2020 V-Rail Upgrades June 17, 2016 09:58AM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 19, 2016 09:21PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 19, 2016 10:37PM |
Registered: 8 years ago Posts: 430 |
Re: Folger Tech 2020 V-Rail Upgrades June 22, 2016 08:06PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 23, 2016 06:54PM |
Registered: 8 years ago Posts: 430 |
Re: Folger Tech 2020 V-Rail Upgrades June 24, 2016 08:50AM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 24, 2016 11:06PM |
Registered: 8 years ago Posts: 430 |
Re: Folger Tech 2020 V-Rail Upgrades June 27, 2016 11:08PM |
Registered: 8 years ago Posts: 30 |
Re: Folger Tech 2020 V-Rail Upgrades June 28, 2016 11:45PM |
Registered: 8 years ago Posts: 430 |
Quote
Brotherbrown831
i just added a simple bit of Gcode to the startup script in my slicer. Very simple to do. The bed takes about the same time to heat up, is uses a larger heater pcb, i would say any larger than this and I would recommend a 120v heater on a relay.
here is my start Gcode:
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G29
M117 Cleaning...;Put Cleaning message on screen
G1 Y304.0 F{travel_speed} ;move the platform back of bed
G92 E0 ;zero the extruded length
G1 F200 E15 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length
G1 X25 F{travel_speed} ;move the platform back of bed
G1 X80 F{travel_speed} ;move the platform back of bed
G1 X25 F{travel_speed} ;move the platform back of bed
G1 X100 F{travel_speed} ;move the platform back of bed
G1 X25 F{travel_speed} ;move the platform back of bed
G1 X100 F{travel_speed} ;move the platform back of bed.
G1 X25 F{travel_speed} ;move the platform back of bed
G1 X100 F{travel_speed} ;move the platform back of bed
G1 F{travel_speed}
;Put printing message on LCD screen
M117 Printing...