Print does not start after BLtouch autolevel December 30, 2020 01:21PM |
Registered: 3 years ago Posts: 2 |
Send: N9 G28*26 Recv: TT::200.56200.56 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::6969 BB@@::2424 Recv: Recv: echo:busy: processing Recv: TT::200.56200.56 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::6969 BB@@::2424 Recv: Recv: echo:busy: processing Recv: TT::200.52200.52 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::6969 BB@@::2424 Recv: Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::8181 BB@@::2424 Recv: Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7979 BB@@::2424 Recv: Recv: echo:busy: processing Recv: TT::200.07200.07 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7676 BB@@::2525 Recv: Recv: echo:busy: processing Recv: TT::200.56200.56 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::6464 BB@@::2525 Recv: Recv: TT::200.52200.52 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::6565 BB@@::2525 Recv: Recv: echo:busy: processing Recv: TT::200.03200.03 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7777 BB@@::2525 Recv: Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7575 BB@@::2626 Recv: Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7474 BB@@::2626 Recv: Recv: echo:busy: processing Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7474 BB@@::2626 Recv: Recv: TT::200.00200.00 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7373 BB@@::2626 Recv: Recv: echo:busy: processing Recv: TT::200.03200.03 //200.00200.00 BB::60.0060.00 //60.0060.00 @@::7272 BB@@::2626 Recv: Recv: echo:busy: processing Recv: TT::200.00200.00 //200.00200.00 BB::60.0160.01 //60.0060.00 @@::7373 BB@@::2222 Recv: Recv: echo:busy: processing Recv: X:155.00 Y:130.00 Z:13.00 E:0.00 Count X:12400 Y:10400 Z:5200 Recv: ok Send: N10 G1 Z2.0 F3000*42 Recv: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) Recv: ok Send: N11 G1 X0.1 Y20 Z0.3 F5000.0*30 Recv: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) Recv: ok Send: N12 G1 X0.1 Y200.0 Z0.3 F1500.0 E15*83 Recv: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) Recv: ok Send: N13 G1 X0.4 Y200.0 Z0.3 F5000.0*55 Recv: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) Recv: ok Send: N14 G1 X0.4 Y20 Z0.3 F1500.0 E30*121 Recv: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) Recv: ok