MPCTEMP M306 T E1 or 2 doesn't work
Posted by SlickNickeL
|
MPCTEMP M306 T E1 or 2 doesn't work January 27, 2023 10:42PM |
Registered: 1 year ago Posts: 10 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 27, 2023 11:13PM |
Registered: 8 years ago Posts: 352 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 27, 2023 11:20PM |
Registered: 1 year ago Posts: 10 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 28, 2023 10:02AM |
Registered: 8 years ago Posts: 352 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 28, 2023 10:29AM |
Registered: 1 year ago Posts: 10 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 05:41PM |
Registered: 1 year ago Posts: 10 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 06:09PM |
Registered: 8 years ago Posts: 352 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 08:53PM |
Registered: 1 year ago Posts: 10 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 09:33PM |
Registered: 8 years ago Posts: 352 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 10:49PM |
Registered: 1 year ago Posts: 10 |
I’m using bugfix 2.1.X
I tried the M306 2.1.2 and it functioned as before. Only way to change is with a T1 or T2
I did M306 E1 T and M306 E2 T and all went to E0
I tried M306 E1 and E2 went to same as M306 and M306 T1 and all went to E0
Edited 1 time(s). Last edit at 01/30/2023 10:54PM by SlickNickeL.
I tried the M306 2.1.2 and it functioned as before. Only way to change is with a T1 or T2
I did M306 E1 T and M306 E2 T and all went to E0
I tried M306 E1 and E2 went to same as M306 and M306 T1 and all went to E0
Edited 1 time(s). Last edit at 01/30/2023 10:54PM by SlickNickeL.
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 30, 2023 11:53PM |
Admin Registered: 13 years ago Posts: 7,147 |
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 31, 2023 12:15AM |
Registered: 8 years ago Posts: 352 |
Here's a couple more attempts at a M306 for bugfix-2.1.x. Both compile without errors.
M306_enqueue_one_now uses a different approach to enqueuing the command than my last attempt.
M306_T_code copies the code from T.cpp.
To be honest, I don't know enough about multi extruder/systems to be have confidence that either approach is a good long term solution. The best long term approach would be to open a bug report and hope one of the Marlin gurus help.
M306_enqueue_one_now uses a different approach to enqueuing the command than my last attempt.
M306_T_code copies the code from T.cpp.
To be honest, I don't know enough about multi extruder/systems to be have confidence that either approach is a good long term solution. The best long term approach would be to open a bug report and hope one of the Marlin gurus help.
|
Re: MPCTEMP M306 T E1 or 2 doesn't work January 31, 2023 12:13PM |
Registered: 1 year ago Posts: 10 |
I couldn’t get either one to compile. It’s not a biggie at the moment. It works well with T1 and T2 prior to M306 T. I did notice that after a T1orT2 then M306 T, it says E0, busy, busy, busy, E1 or E2 then shows and the correct head is tested. M500 and it’s all good. M306 reports correctly to the changes.
As we get into 3 head manufacturing, this will need to addressed. I will put in a bug report.
As we get into 3 head manufacturing, this will need to addressed. I will put in a bug report.
|
Re: MPCTEMP M306 T E1 or 2 doesn't work February 12, 2023 10:39AM |
Registered: 8 years ago Posts: 352 |
Sorry, only registered users may post in this forum.