Welcome! Log In Create A New Profile

Advanced

Noob requiring assistance

Posted by Nylkos 
Noob requiring assistance
February 28, 2017 12:08PM
Hi, I would like some assistance.

I am currently building a CoreXY 3D printer.

The board that I am using is the Duet 0.8.5.

I am going to run with 2x power supply 24V but, while I am learning, I am using an old ATX 12V power supply. At the moment, I can't seem to run my stepper motors or fan with Ponterface. I am afraid that my 0.8.5 might be damaged is there a way to run a diagnostic on the Duet 0.8.5?

I am unsure of what I could provide that could indicate the issues...

IF I do the M115 (in the Adruino program), I get the message : "FIRMWARE_NAME:RepRapFirmware FIRMWARE_VERSION:1.09 ELECTRONICSgrinning smileyuet (+ Extension) DATE:2015-04-21" so I know it responds...

I used [reprappro.com].

But I might just restart everything from the duet3d.com documentation... but the link isn't valid.

Thank you for your assistance.

Edited 1 time(s). Last edit at 02/28/2017 12:10PM by Nylkos.
Re: Noob requiring assistance
February 28, 2017 01:35PM
Update the firmware & DWC, 1.09 is old. See [duet3d.com] and [duet3d.com]

Use [configurator.reprapfirmware.org] to setup the config.g and other needed files.

The connections on the 085 and Wifi are similar except for the network setup. The configurator web site will get the network setup properly for the board.

[reprap.org] will help on the connections.

Edited 1 time(s). Last edit at 02/28/2017 01:36PM by stephenrc.
Re: Noob requiring assistance
February 28, 2017 02:51PM
Maybe you have SD-card issues and the config.g doesn't load? Can you send a M503 from Pronterface and see if it returns any configuration info?
Re: Noob requiring assistance
February 28, 2017 06:10PM
ok Thanks for the comments...
Here is what I have done and the result.

I upgraded (bossac) to the 1.17e.bin. the web service that I found was 1.14a.bin unsure if it's the right version...

Since I am learning I copied the 1.14a to the /sys folder and tried the M997 S2 to install the web service and I got
Quote

Invalid module number '2'
.
Have I done anything wrong? should I downgrade to 1.14a for the Bossac?

The M503 worked... the SD card responded

Edited 1 time(s). Last edit at 02/28/2017 06:48PM by Nylkos.
Re: Noob requiring assistance
February 28, 2017 07:35PM
I was finally able to run the stepper motors, my 0.8.5 isn't blown...

Also I would require some help on how to install the Web Controler.
I copied the DuetWebControl-1.14a to the /www
I copied the files DuetWebControl-Master to the /sys

When I am trying to run M997 S2 to install it doesn't install

Edited 1 time(s). Last edit at 02/28/2017 07:50PM by Nylkos.
Re: Noob requiring assistance
March 01, 2017 03:06AM
I'm glad you got it working. DuwtWebControl 1.14a is the correct version to work with RRF 1.17e. M997 S1 and M997 S1 are for the Duet WiFi only.

Edited 1 time(s). Last edit at 03/01/2017 03:06AM by dc42.



Large delta printer [miscsolutions.wordpress.com], Robotdigg SCARA printer, Crane Quad and Ormerod

Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Re: Noob requiring assistance
March 01, 2017 02:17PM
Quote
dc42
I'm glad you got it working. DuwtWebControl 1.14a is the correct version to work with RRF 1.17e. M997 S1 and M997 S1 are for the Duet WiFi only.

For the Duet 0.8.5 do I require to do something to install the web control or do I just need to setup the network specs?
Re: Noob requiring assistance
March 01, 2017 02:47PM
Quote
Nylkos
Quote
dc42
I'm glad you got it working. DuwtWebControl 1.14a is the correct version to work with RRF 1.17e. M997 S1 and M997 S1 are for the Duet WiFi only.

For the Duet 0.8.5 do I require to do something to install the web control or do I just need to setup the network specs?

You just need to extract the contents of the DuetWebControl zip file to /www on the SD card, and set up the network IP address in the M552 command in config.g.



Large delta printer [miscsolutions.wordpress.com], Robotdigg SCARA printer, Crane Quad and Ormerod

Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Re: Noob requiring assistance
March 01, 2017 03:20PM
Will do once I get home.

Thank you all for your help.
Sorry, only registered users may post in this forum.

Click here to login