mini height sensor triggering
Posted by Gaou
|
mini height sensor triggering August 27, 2017 01:16PM |
Registered: 7 years ago Posts: 294 |
Guys i thought i ll give one more go to z axis homing as the last months i did that manual . But yesterday i started fooling aroung i saw it gets a false triggering when it is at 10mm-20mm ( dont remember where exactly ) .
So what am i doing wrong and get this triggering ?
Any ideas you can come up with would be perfect.
I am using the mini height sensor from dc.
Delta Printer
Duet 0.8.5 firmware 1.19
So what am i doing wrong and get this triggering ?
Any ideas you can come up with would be perfect.
I am using the mini height sensor from dc.
Delta Printer
Duet 0.8.5 firmware 1.19
|
Re: mini height sensor triggering August 28, 2017 04:29AM |
Registered: 9 years ago Posts: 14,639 |
If you are getting false triggering at height, and it isn't caused by direct bright sunlight reflecting off the bed into the sensor, ask me or whoever you bought it from to replace it.
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
|
Re: mini height sensor triggering August 29, 2017 07:07AM |
Registered: 7 years ago Posts: 294 |
the sensor works pretty ok David. i dont think it has a hardware problem ( i cant understand it at least..) . It triggers how it should be close to the table, but it also triggers at 8.15mm height. so when i am switching the printer on it has to be closer than 7mm height to get a proper trigger ....!
I bought it from you David .
Delta Printer
Duet 0.8.5 firmware 1.19
I bought it from you David .
Delta Printer
Duet 0.8.5 firmware 1.19
|
Re: mini height sensor triggering August 29, 2017 10:58AM |
Registered: 9 years ago Posts: 14,639 |
Send me a PM with a note of your invoice number if you have it, email address and approximate purchase date, and I will send you another sensor. A small number of sensors have that problem due to tolerances in the IR LEDs, but our test procedure doesn't catch it.
Edited 1 time(s). Last edit at 08/29/2017 11:00AM by dc42.
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Edited 1 time(s). Last edit at 08/29/2017 11:00AM by dc42.
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
|
Re: mini height sensor triggering September 03, 2017 01:48PM |
Registered: 5 years ago Posts: 3 |
|
Re: mini height sensor triggering September 03, 2017 02:10PM |
Registered: 9 years ago Posts: 14,639 |
When you get false triggering, is the LED on the sensor steady red or is it blinking rapidly?
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
Large delta printer [miscsolutions.wordpress.com], E3D tool changer, Robotdigg SCARA printer, Crane Quad and Ormerod
Disclosure: I design Duet electronics and work on RepRapFirmware, [duet3d.com].
|
Re: mini height sensor triggering September 03, 2017 03:21PM |
Registered: 5 years ago Posts: 3 |
|
Re: mini height sensor triggering September 29, 2017 03:40AM |
Registered: 8 years ago Posts: 1,699 |
I recently bought one sensor from makerdise.com and a second one is on its way. Could I have this problem, too? Should I check them? And how? I will use them about the end of the year.
Before my OM2 burnt I could test it on black aluminium. The results were spectacular.
Slicer: Simplify3D 4.0; sometimes CraftWare 1.14 or Cura 2.7
Delta with Duet-WiFi, FW: 1.20.1RC2; mini-sensor board by dc42 for auto-leveling
Ormerod common modifications: Mini-sensor board by dc42, aluminum X-arm, 0.4 mm nozzle E3D like, 2nd fan, Z stepper nut M5 x 15, Herringbone gears, Z-axis bearing at top, spring loaded extruder with pneumatic fitting, Y belt axis tensioner
Ormerod 2: FW: 1.19-dc42 on Duet-WiFi. own build, modifications: GT2-belts, silicone heat-bed, different motors and so on. Printed parts: bed support, (PSU holder) and Y-feet.
Ormerod 1: FW: 1.15c-dc42 on 1k Duet-Board. Modifications: Aluminium bed-support, (nearly) all parts reprinted in PLA/ ABS, and so on.
Before my OM2 burnt I could test it on black aluminium. The results were spectacular.
Slicer: Simplify3D 4.0; sometimes CraftWare 1.14 or Cura 2.7
Delta with Duet-WiFi, FW: 1.20.1RC2; mini-sensor board by dc42 for auto-leveling
Ormerod common modifications: Mini-sensor board by dc42, aluminum X-arm, 0.4 mm nozzle E3D like, 2nd fan, Z stepper nut M5 x 15, Herringbone gears, Z-axis bearing at top, spring loaded extruder with pneumatic fitting, Y belt axis tensioner
Ormerod 2: FW: 1.19-dc42 on Duet-WiFi. own build, modifications: GT2-belts, silicone heat-bed, different motors and so on. Printed parts: bed support, (PSU holder) and Y-feet.
Ormerod 1: FW: 1.15c-dc42 on 1k Duet-Board. Modifications: Aluminium bed-support, (nearly) all parts reprinted in PLA/ ABS, and so on.
|
Re: mini height sensor triggering October 30, 2017 10:08AM |
Registered: 7 years ago Posts: 294 |
Sorry, only registered users may post in this forum.