Show all posts by user
General discussions. For specific printers / electronics / fabrication methods / softwares, please see other sections.
[Netherlands] Fully operational Shapercube for sale €1200!!!! - 13 years ago
Hello, Fully operational Shapercube 3D printer for sale. The Shapercube as built last year. I'm now building my own design, so I want to sale this one. I have provided it with a heated print bed and RAMPS 1.3 electronics. On the side, I've made a spool holder. Apart from those adjustments, the printer is in original state. The Shapercube is known for its durability and toughness. The printer iby mathijs.kossen - For Sale
Re: Layer shifting - 13 years ago
It shifts echt time at the same moment when printing a single object multiple times...by mathijs.kossen - General
Layer shifting - 13 years ago
Hi Guys, I'm printing with a shapercube. Sometimes, only when I do not print the calibration square, my layers shift. After two, three of four layers, it moves a few centimeters to a random side. I use SFACT to create G-code and pronterface as host software. Does anyone experienced any of this? Reg, Mathewby mathijs.kossen - General
Kapton reseller - 13 years ago
Hello, i;m looking for a easy way to get some (wide) kapton tape. I live in the Netherlands, so ordering it from makerbot each time is expensive and takes long. Is there any alternative of known resellers where i could buy it?by mathijs.kossen - General
Re: Mendel bouwer (beginner) - 13 years ago
Hoi Ids, Ik ben geboren in de wieringermeer polder, dus kom naar nog wel eens terug. Zelf woon ik in Amsterdam. Ik ben net klaar met het bouwen van een shapercube, maar ben daardoor ook geintereseerd geraakt in andere modellen. Ik zal het laten weten als ik in de buurt ben, misschien kan ik een keer langskomen. Gr, Mathijsby mathijs.kossen - Dutch User Group - Archive
Kapton - 13 years ago
Hallo, ik ben sinds vandaag begonnen met het printen met mijn shapercube. Hij is gecalibreerd, maar inmiddels is mijn kaptop tape om mee te printen op. Waar kopen jullie kapton tape, of is er iets anders 'makkelijk' verkrijgbaar om op te printen? Gr, Mathijsby mathijs.kossen - Dutch User Group - Archive
Extruder jam - 13 years ago
Hello, for some time i'm struggling with my extruder. I'm building a shapercube, with a pre-made extruder. (see link below). The problem is, as i've read more about on all fora, that it gets jammed. My shapercube uses a Wade's geared extruder I try to extrude ABS at a temperature of 240C, but it neither works at 250C. I ordered a new extruder, which i only use for extrusion of ABS. SO i don't usby mathijs.kossen - Plastic Extruder Working Group
Re: Extruder delayed jam - 13 years ago
Viktor, this is indeed what i did a few times (out of enthusiasm to see wether it would work with PLA as well). I'll clean it with acetone over night. thnx for your repsonse!by mathijs.kossen - Reprappers
Extruder delayed jam - 13 years ago
Hello! I'm almost done building a shapercube, but having some problems with the extruder where i can't find much about on the forum. Before I start to explain, I notice the equipment you use had a lot of influence on the problem solving; so some information about my printer: Shapercube 2.0 I use a Wade's extruder PLA filament (3mm). My hot end was delivered pre-ensembelled: I tried differby mathijs.kossen - Reprappers
Extruder delayed jam - 13 years ago
Hello! I'm almost done building a shapercube, but having some problems with the extruder where i can't find much about on the forum. Before I start to explain, I notice the equipment you use had a lot of influence on the problem solving; so some information about my printer: Shapercube 2.0 I use a Wade's extruder PLA filament (3mm). My hot end was delivered pre-ensembelled: I tried different tby mathijs.kossen - Mechanics
Re: Wade extruder hobbed bolt - 13 years ago
I made my own hobbed bolt by filing some slits in an M8 bolt, this gives a lot of power, enough to push the filament. Though this is on a shapercubeby mathijs.kossen - General
Re: Elastic material - 13 years ago
Hi Rhmorrison, thank you for your quick response. I already tries the soft PLA indeed. This yields a little flexible material but nog yet flexible enough. I would like to be able to print for example a table mat which can be fold double completely.by mathijs.kossen - Altes Forum
Elastic material - 13 years ago
Hello, I'm looking for a kind of material which has elastic properties after printing. For example to make a tiny part of a hose of an holder to freeze ice cubes in the fridge. Does anyone maybe have experience on this area and/or could me help find some sort of material? Kind regards, Mathew (Netherlands)by mathijs.kossen - Altes Forum
Flexibel printen - 13 years ago
Hallo, Ik ben al enige tijd op zoek naar een materiaal met flexibele eigenschappen (elastomeer) na het printen. Waarmee je bijvoorbeeld een stukje tuinslang zou kunnen maken, of een kort verloop-stukje. Er is een topic over soft-PLA, dit is niet flexibel genoeg om echt bochten mee om te gaan. Heeft iemand verstand van materialen en/of enig idee waarmee en of dit mogelijk is? Bedankt, Mathijsby mathijs.kossen - Dutch User Group - Archive