My Z speed float max_feedrate[] = {200000, 200000, 240, 500000}; was too high. Changed down to 170.by [email protected] - General
So I am using Sprinter, I have the same Problem, but do not have those Variables.... Exact same diagnosis, just squirts all the layers into the same Z height, but normal manual control. Repetier shows Z coordinates fine, and the feed calibration is fine. I dont know what to fiddle with!! Could anyone take a peek? RepRap Mendel w Ramps1.4, Sprinter, Slicer, Repetierby [email protected] - General
I have an Orca 043, Marlin FW and gen 6 deluxe. The first command from Repetier takes a good 40-60seconds to go through and everything else cues up. Any ideas?by [email protected] - Firmware - mainstream and related support
I can send a few good commands, then machine freezes, there is the ????? line and nothing except the "commands waiting" cue keeps rising when more commands are sent. A reconnection will let you do another two or three commands and then its off again. I will re-flash it with both fingers crossed! The fact that it moves at all should mean the motor drivers and circuitry is ok? amirite? Thanks!!by [email protected] - Repetier
Our Gen 6 board is throwing mysterious ????????????????????????????????????????????? Line: replies in the Repetier console and becoming unresponsive. Recently it had been left in a jam that probably left it straining against its-self for some time, Is it possible something on the board is blown and what are good ways to test for hardware damage? As the Gen6 is one piece unlike the RAMPS systby [email protected] - Repetier
Generative Modelling, or Procedural Modelling, these are things i have found. These are all closed models still, I would still like to hear about shaping the fill if anyone knows anything.by [email protected] - Let's design something! (I've got an idea ...)
I have been dreaming up ideas for "scaffolding" function objects since my first viewing of a 3D print, I found the fill fascinating. Please tell me if this exists and what the tools are? I would like to know how or develop a way to print wall-less objects as scaffolding/support, similar to some of the bio-strata projects I have seen. or perhaps a very thin structure like those spring spokes on sby [email protected] - Let's design something! (I've got an idea ...)
I have tethered all the unnecessary pins and low active pins to ground, and linked the Gnd Pin to the ATX supply ground to stabilise the Grounding. I have tried both HI and LOW settings for the Opto pins cos it could be one or another. The motor is engaged (´cannot move and hums a little.) but does not move. I understand it is a two wire system? Pulse and Direction?? I Have looked at other drivby [email protected] - Stepper Motors, Servo Motors, DC Motors
If my WadesExteruder is going hissssssTIC-hissssssTIC and while ticking is turnable by hand am i looking at worn-out motors, broken drivers or too-tight filament/e-Feedrate?? Its not extruding nearly enough for the models i print, they come out like piles of lumpy spiderweb despite being awesome only 3 days before.by [email protected] - Mechanics
...even when they are going just fine! -I though of overheating but I have a fan, heatsinks and thermal paste on the polulus. -I tried a hollow model to see if time/workload had anything to do with it but no love. I have also done demanding horizontal prints just fine. -The fan on the powersupply keeps whirring, but Pronterface says "disconnected", and when I try to steer manually it locks up.by [email protected] - Printing
I recently repaired an old Mendel and I broke, repaired then lost the only hard-to-source part: the Thermal Barrier. See: I am having trouble finding a v5 (ie: 16mm) fitting or a PTFE rod that I can lathe into shape. All the new versions all use 10mm rod. No, I do not want to buy an 80€ replacement hot-end for lack of a 5€ part. All the stores need 30€ shipping for a 5€ piece or demand I buyby [email protected] - Austria RUG
I recently repaired an old Mendel and broke, repaired then lost the only hard to source part: the Thermal Barrier. See: I am having trouble sourcing a v5 (ie: 16mm) fitting or a PTFE rod that i can lathe into shape as the new versions all use 10mm rod. No i do not want to buy an 80€ replacement hotend for lack of a 5€ part. All the stores need 30€ shipping for a 5€ piece or demand I buy andby [email protected] - Wanted