Show all posts by user

Re: AWorldnet A600 Not Working - 11 years ago

i have e3d extruder bowden tipe and i even printed out the mount for it. if you want i can send it to you. it fits on aworldnet carriage... i have to put it on again, now when my extruder motor doesn't skip steps any more

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

i was soooooo pisted off with that but i managed to repair it and to buy some extruder time to print another one.... i found on marlin board pot to increase the power for extruder so now it doesnt missing steps any more..... at least that

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

thank you very very much!! i'll try to upload and start tweeking..... as soon as i solve this problem.... my exruder breaked....

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

Thanks man! looling forward to it

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

jes, i have lcd but no autoleveling....so far

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

Hi! nice that you have running it again i understand the frustration, had the same problem with my extruder. I managed to break the threads in my alu block when i was replacing the hot end. fortunately my friend sugested to use teflon tape and now everything is running where it should. i have the spare ramps and i wolud be interested in firmware once you get it running if it is not too much tro

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

QuoteZavashier Quotedarac_komaracim using abs it was 230 for nozzle, and 80 for heatbed You should at last reach the glass temperature of the plastic with the heatbed. For ABS it's around 105°C. If you set your heatbed under 105°C it's not realy effective. jeah, by trial and error a found for my abs was 147 for extruder and 104 for hotbed. im using stick glue for adhesion and it works wonders!

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

now with new abs the settings are 247c for nozlle and 96 for heatbed. i also had to start using hairspray for beter adhesion and i found that it sticks more firmly if you apply it when you heat the heatbed. and even more if you set the skirt in cura. got the better results if i start the cooling fan of the nozzle after 1cm of print (on z) and only 15-20 %.

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

Hi davy, yes i had progress. The machine is working now, all to all it is what i paid for . Im learning to work around it. i found that if i leave extruder head near heatbed when worming up the heatbed the fan on extruder head ( the one on the heatsink) cools the heatbed so it can't reach more than 86C and im using new abs that needs 96c (found by trial and error). So i have to retract the z a

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

aha, that what im using abs it was 230 for nozzle, and 80 for heatbed

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

I found the problem the end stop switches were on the wrong places on board so there was a problem with home position! i tryed to print your cube but there was warping, i prezume because the temperature of the heated bed was too low (50 or so) so i opened the cura and made a robot i think i need a new nozzle because this has taken a beating quite bed not bad for first print.... now the fu

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

Thanks man, that helps a lot! i'll try it tonight ! darko

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

when im using cura i don't need the repetiere? or am i missing something? im guite newbie in 3d printing

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

im using slicer (trying to use ) i will try tonight when i get home, also i will send you generated g code so you can check if it is not much trouble for you. tnx a lot darko

by darac_komarac - General

Re: AWorldnet A600 Not Working - 11 years ago

Hi guys, i bought the sam eprinter and i have problems with setting the zero point. i can set it manualy but when i reach the endstop on z axis and the printer want allow me to move it any more. whitch is ok but when i move it on the opposite directione every time i got the massage that the endstop is reached and i cant move it back to the endstop? and when i try to print the the z axis just sl

by darac_komarac - General