some years back there was a program that would allow you to "look" at your Marlin firm ware and also a newer UPDATE so you could compare the two side by side, does any one know where I can download it? Thank you for any help.by yar60 - General
I have a question.... I'm rebuilding my old i3 mandel printer and would like to know if and where I can find the new 20x20 rail pattern for the Z axis to print I've seen it once and be darn if I can find it again... also on the new MKS Gen v1.4 3D Printer Controller Board where do i find how to use a single cable display cord or is that possible? i have a display screen but it only use a single cby yar60 - General Mendel Topics
I'm having a little problem with the new Marlin Firmware 1.1.9 "I think" got most of the bugs out of it thanks to you all but still one major problem in the drifting on my "Y" axis. not sure what the real problem is my printer has been working just fine for over 3 years now, all I did was up-date to the new firm ware and this, one print is just fine and the next came from outer space some where.by yar60 - General
Thank you, That was the problem so I put a thermal blanket om the bottom of the heatbed and now it holds the temp all the way to 100 just right, again thank you for your help.by yar60 - General
I'm having a problem with my Heat bed, does any one know anything about the new updated Marlin firm ware, checked all the setting and it's not working get to 71 C and "bed Heating Failed" whats up? not sure even what lines to copy to look at anymore. I have a Reprap Prusa i3 Mandel , 270x220x180mm, the hot end is a All Metal J-head Hotend for 1.75 mm Bowden Extruder Ramps 1.4 Marlin 1.1.9 firmwby yar60 - General
does any one know anything about the new updated Marlin firm ware? I installed it and every thing works except my exturder.. I have checked the motor and it works just fine... here are the command lines for the extruder what I;m I missing? // @section extruder // This defines the number of extruders // :[1, 2, 3, 4, 5] #define EXTRUDERS 1 // Generally expected filament diameter (1.75, 2.85, 3by yar60 - General
I would like to know if: 1. I have a Ramps 1.4 control board on a Prusa i3 Mandel printer (HIC) reworked... my hot end is a J-Head from (China), what is the max temperature that this head can operate at? 2. On my Ramps 1.4 control board can I set it to operate at 260 plus C. ) 2016 MarlinFirmware with up dates, I would like to use Nylon to print with and I understand I need more heby yar60 - General Mendel Topics
what code do i add to get the bed to shut down after printing. my g code: M104 S0 ; turn off temperature G28 X0 ; home X axis M84 ; disable motors thank you for any help.by yar60 - General
does any one happen to know why this is happening to my prints, check photo.by yar60 - General
Trying to print and i kept getting a: (THERMAL RUNAWAY) Why?by yar60 - General
Ok so how do i defined "extrude threw an extruder that isn’t at minimum required temperature" how do you get the 2 extruders at 0 degrees? any where I can read more information so I could get the 2 extruders to work. went back to a single extruder. Thank you for any help.by yar60 - General
Dust change to eeb went okay one more question i get error : MINTEMP.......Why? thank you.by yar60 - General
Thank you. again for your help, Oh hope you had a Merry Christmas and have a happy New years.by yar60 - General
this is the error I get, trying to setup a dual extruder on my prusai3 Mandel. Error: Arduino: 1.6.9 (Windows 8.1), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from sketch\Configuration_adv.h:659:0, from sketch\Configuration.h:943, from C:\Users\Ray\Documents\Marlin-1.1.0-RC5\Marlin\Marlin.ino:37: SanityCheck.h:400: eby yar60 - General
Does anyone have a copy of 3D print Tech 2.0 would like to get a copy.by yar60 - General
Who is the Head of this forum? Does he have an E-mail address? Thank you I do hope I don't put anyone out.by yar60 - General
Thank you, does it matter if your printer is open in the front? I see that some Printers are closed all around, I have to back closed but the front half is still open. again thank Ill try increasing the temp.by yar60 - General
#1 Printing fine except in 2 or 3 places it's as if it skipped layers... #2 The bottom half was so/so and then the top half went to hell in a hand basket. The Balls on the inside where the same way bottom ½ ok top ½ really bad, #3 Same Picture (2) looking at the side of it bottom so,so top ??????? #4 Came out perfect.. #5 spool spacer came out perfect. All the prints are ABS, bed teby yar60 - General
my REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER. works but doesn't work, none of the controls work. press the button down and it shows the: 1 screen information press down again returns to main screen. 2 prepare nothing 3 control, nothing but will not work beyond that.it reads the temp, Bed, Hotend and the other information but thats all. here what i installed. is there something I misseby yar60 - RAMPS Electronics
I would like to know how to set up a Volcano hot end or have a few pictures of one set up and on a printer.by yar60 - RAMPS Electronics
how do you stop your Extruder from "spitting" the filament out, it's as if the extruder is cutting in and out not a steady flow. what setting do i need to adjust.by yar60 - RAMPS Electronics
Dust A Question: I have 3 pictures of test printing I would like to know is the bed to hot or to cold / or is the extruder to hot or to cold? going to fast or to slow? Thank youby yar60 - RAMPS Electronics
Does any one know why the extruder would "chatter" it seams like it wants to go both ways at the same time. Plug it in and sat it on the bed and it almost danced it's way off. setting: //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit //can be software-disabled for whatever purposes by #define PREVENT_DANGEROUS_EXTRUDE //if PREVENT_DANGEROUS_EXTRUDE is on, yby yar60 - Reprappers