Thanks guys. I will give that a go, things seem to be working a little better. Also. Once I have calibrated and leveled for the first time, do I am not sure what to run and when. Printer Startup - Do I need to set zero or just home it? Calibration - done once in a while right and not all the time? Print Start - Reference mesh and homeby onefishtwofish - General
I have successfully added the piezo sensor to my dbot with a duetwifi. Problem I have is that now, when starting the print, it is at 0 and does not move up to .3 even though I have it at .3 in cura. I have no idea why it is not moving up to the initial height. Any thoughts? I am pretty confused as to why it won't sent the initial layer hieight even though zprobe height is 0. Config.g ; CoreXby onefishtwofish - General
Understood. Thanks for all the help Elmo... back to the drawing board.by onefishtwofish - General
Readjusted the left pot. - more sensitivity. - LED is triggering with the slightest touch - Same slow response from webserver and your explanation makes sense but seeing range from 17-700 Ran G32 again - Bed goes down a bit - Bed moves up like it wants to probe - Touch end of nozzle - Bed doesn't stop - Press hard on nozzle and bed doesn't stop Power down printer to prevent bed from smashingby onefishtwofish - General
Yes. It is very sensitive to the touch. One thing I do notice is that even though I am getting the blue LED trigger light, I have to press pretty hard to get a reading on the web portal unless I press somewhat hard. Couple thoughts: -Could it be how much I tightened the top part of the connector to the v6? My thought is no, if the LED is lighting, it is reading the pressure. -Why do I haveby onefishtwofish - General
So after I enter G32 The bed goes down a bit, then starts its move up to the nozzle. The z-probe reading definitely went up to 765 reading on the web portal, when I pushed it with my hand. It just doesn't stop the bed. (FYI, I fixed the z connectors so now the bed goes in the proper direction.)by onefishtwofish - General
Looking at my connections to the board, I think I have my z reversed. Which is why all of my settings are backwards. Up = +n Down = -n. I should change it, will make it easier when researching. It just even isn't probing, Do I need to have these uncommented? ; Z probe M558 P1 F500 X0 Y0 Z0 ; Analog Z probe, also used for homing the Z axis G31 X0 Y0 Z0 P20 ;by onefishtwofish - General
Odd. I am getting the reading on the Web Portal but even at 10, it is not stopping the bed. No error in the gcode also...i Here is my bed.g ; Auto calibration routine for delta printers ; Before running this, you should have set up your zprobe Z offset to suit your build, in the G31 command in config.g. M561 ; clear any bed transform, otherwise homing may be at the wrong height G31 X0 Y0by onefishtwofish - General
Thanks for the respons Dj. Ok. So I have made the adjustments. - It now triggers correctly - Duet web console is showing pressure on z-probe - Starts at 0 and goes up to 1000 - Probe Set up now looks as follows (which seems to work) ---M558 P1 F500 X0 Y0 Z0 ---G31 X0 Y0 Z0 P500 Running the Probe When I use G32 (which runs bed.g) it starts bringing the bed up for probing Message: Bed equation fiby onefishtwofish - General
That seems to have done the trick. The left adjuster: The unit I bought came prebuilt. Unfortunately for my V3 and Hotend Mount I needed the other mount to connect it to my carriage. I printed the one you supplied on your site and it mounted nicely. I have a couple questions on tuning. 1. Can you overtighten the top piece to the point where it will will affect the reading? I am not sure if Iby onefishtwofish - General
Hello there, I just received your sensor and have been trying to configure it for the past few days on a DBOT / DUETWIFI. I am running into a couple problems and wondering if you could help. The trigger seems to be backwards. When it is lit it is registering as "not triggered" the blue light is on. If I run G30 in the gcode console and the blue light is off, it shows "Error: Z probe already trby onefishtwofish - General