Dust Thank you for the explanation, now I understand. Not important in some ways but I also notice the line 77 #define STRING_CONFIG_H_AUTHOR "(Bob Kuhn, Anet config)" does not seem to translate to the LCD on my printer nor does it appear with an M115. Cheersby Leslieval - Firmware - Marlin
Dust a follow up question if ok. I was fortunate to have you provide the advice and details for changing the line in the Configuration_adv.h file resolving my compiling issue with the marlin version and configuration files i had downloaded from Github. I am wondering what i had done incorrectly to require this code line change you provided or what i would be better to do in the future when downloby Leslieval - Firmware - Marlin
Hello Dust, following up on this post after you so magnificently helped me in the previous one i am hoping you may be able to advise where i am going wrong perhaps in my settings I have an ATMega 1284p (Anet 3d V1-5) board and it is currently managing the mesh leveling with a submenu on the lcd. The lcd that came with my printer. I have seen when compiling for the machine that i get a referenceby Leslieval - Firmware - Marlin
Dust, GENIUS. Made the change you gave me and it worked perfectly. Then edited configuration.h and enabled mesh-bed-levellin, Lcd-menu, level after g28 and it all compiled perfectly. Thank you, thank you, thank you. I have been wrestling with this and other problems in compiling Marlin using VSCode and Platformio off and on for a year but being forced to isolate as i fight off covid means i havby Leslieval - Firmware - Marlin
Dust, thank you for your reply and help. After my post I did re-read the github page and as you have siad it was pretty clear. I had previous to your message downloaded the configs for 2.0.9.3 from the drop down list and received the error I posted in an edit to my earlier post. I then used the spreadsheet option on github and downloaded the zip for 2.0.9.3 and used that in a compile and unforby Leslieval - Firmware - Marlin
Hello, I have been attempting to compile Marlin 2.0.9.3 for use with my Anet A8. I have used the configuration files downloaded from Github and selected the Anet A8 files from those and pasted them in to my Marlin 2.0.9.3 folder. I can se from the files this configuration file was prepared by Bob Kuhn who I see is regularly represented in these chat rooms. My first problem is the following atby Leslieval - Firmware - Marlin
Hello, I am trying to complile a Marlin 2.0 (2.0.7.2)Build using VSCode, PlatformIO and Marlin build. I have taken forever to get to the stage where I am but still have some problems I need help with and sure hope someone can advise. The current problem is I wish to use manual mesh bed levelling on my printer and I can compile the build with that option uncommented in Configuration.h but only ifby Leslieval - Firmware - Marlin
Hello and thank you for your reply. My apologies for my delayed response. I have just recently had my Covid shot and had a mild reaction to it but no complaints. I am now back in my office and on restarting my printer and homing it I can see it is now showing z = 0 so the -0.05 has now magically disappeared:-) I had restarted my printer several times before my previous post so unsure how it waby Leslieval - General
Thank you for responding mechabits. I am not sure what you mean by baby stepping offset persisting? I have turned the printer on and off several times so i assume that would reset Marlin for any tuneing changes i might make when printing. Is there something i should be looking at? Cheersby Leslieval - General
Hello, I am sure someone can help me with what is probbly a very simple solution to my probably very basic question? My printer is using Marlin 2.0. I have set Configuration H parameters as follows // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS -15 #define Y_MIN_POS -10 #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE #defiby Leslieval - General