Show all posts by user
General discussions. For specific printers / electronics / fabrication methods / softwares, please see other sections.
Re: [Help needed] Pursa i3 Rework with marlin firmware - 8 years ago
Did you try pid tuning?by Frans@France - Reprappers
Re: New to ABS - Filament Slips After Printing 20-30min - 8 years ago
Quotethe_digital_dentist the extruder motor should skip. My extruder motor did not skip, the Wade gear broke Used friction welding with a dremel to repair it and used it to print a new gear The repaired gear was so strong that I keept it on the printer until it broke for a second time (serval weeks later)by Frans@France - Printing
Re: TB6600 stepper driver Ramps 1.4 connection - 8 years ago
Just wired it to a Arduino board directly so you can write your own code, that will allow you to control the pulse length. It would also allow you to test if the EN must be high or low to enable the driver. I used a TB6560 without any problems.by Frans@France - Reprappers
Re: Filament extruder - 8 years ago
looks like a noztek clone. When running an extruder normally the first feet or so is not usable so when running that 25kg in 25 x 1kg batches you would get ~24,5kg filament. Then again maybe they did not clean the barrel and you lose the first 1 kg to cleaning the barrel.by Frans@France - General
Re: Layer thickness and printing speed. - 8 years ago
Maybe this read could help It refers to this test object :by Frans@France - Printing
Re: dutch filament suppliers - 8 years ago
Have a look at the section.by Frans@France - Extruder, Hotend en Filament
Re: TB6600 stepper driver Ramps 1.4 connection - 8 years ago
Is that >10μS the pulse length? Because if I'm not mistaken the length on Marlin is around 2μs so some programming might be needed.by Frans@France - Reprappers
Re: Best ( simplest ) controller - 8 years ago
Quotethe_digital_dentistIt is definitely common, but the motor driver modules are easy to blow up, But that has nothing to do with the ramps/Arduino but with the design of the driver module. And also it's very easy to connect an other more robust driver to the ramps. The best way I found to blow up the stepper module is by moving the X Carriage on my Prusa I3 fast and serveral times by hand. Qby Frans@France - General
Re: TB6600 stepper driver Ramps 1.4 connection - 8 years ago
The pictures on forum might help orby Frans@France - Reprappers
Re: E3D V6 clone quality ? - 8 years ago
QuoteKoko76If you don't get that you can't make money in a market that won't support it and won't embrace your quality you should be done. Could not disagree more! The pure and simple fact that the clones and knockoffs are available in large quantities or beter flood the market means that it becomes harder and harder to understand the price difference. So while the market would support the higheby Frans@France - General
Re: E3D V6 clone quality ? - 8 years ago
QuoteGovahnator i think the original is way overpriced ( i have the original 1 v5 and 2 v6's as well). I disagree, that money is needed to continue doing business and doing research likeby Frans@France - General
Re: Filament extruder - 8 years ago
Na een berg programmeerwerk tijd om ook de hardware er weer aan te hangen. Na wat kleine aansluit problemen blijkt eea goed te werken. Grootste probleem is echter het aansluiten van de dikte sensor op basis van een Teensy 3.1. SPI werkte niet, I2C bleek onbetrouwbaar (hangen) en eigenlijk onmogelijk als het binnen een interrupt routine word aangesproken. Uiteindelijk werkte een simpele Serial1(by Frans@France - Projecten
Re: E3D V6 clone quality ? - 8 years ago
mhhh forgot the link in my posting :by Frans@France - General
Re: Bowden of Direct? - 8 years ago
QuotestofstikWat denk jij dat de reden is? Waarschijnlijk niet genoeg spanning op de belt waardoor het lagere gewicht van de Bowden minder problemen geeft.by Frans@France - Extruder, Hotend en Filament
Re: Hoe werkt deze ? - 8 years ago
Volgens mij is die inham rechts boven special bedoelt voor je vinger(s) zodat je de veer in kan drukken. Daarmee komt de roller van de hobbed bolt/gear af en kan je het filament eruit halen. Door die inbusbout uit of in te draaien zet je de veer losser of strakker en dus meer of minder druk op het filament. denk ikby Frans@France - Extruder, Hotend en Filament
Re: Bowden of Direct? - 8 years ago
QuotestofstikDeze gast zweert in dit filmpje bij een bowden setup: Tja...maar wel om de foute redenby Frans@France - Extruder, Hotend en Filament
Re: Best ( simplest ) controller - 8 years ago
Arduino Mega & RAMPS with Marlin software, just works, is very cheap, large user group. Getting the settings correct in configuration.h is not the most easy thing ever but it helps to get a better understanding of your 3D printer so I see that as a plus not a min When buying your stepsticks (often included in the Arduino/ramps/lcd packages on ebay) get two extra and a small ceramic screwdriby Frans@France - General
Re: E3D V6 clone quality ? - 8 years ago
Have a look at this thread to see another example of a E3D clone you don't want to buyby Frans@France - General
Re: Bowden of Direct? - 8 years ago
QuoteReplacek heb wel het idee dat de boel wat mee door druppelt als hij geen filament feed doet, door compressie in de lange aanvoer. Zou dat zo kunnen zijn ? Ja, oozing schijnt een probleem te zijn van een Bowden.by Frans@France - Extruder, Hotend en Filament
Re: Ik wil een nieuw hotend bouwen. - 8 years ago
Ja dit is de hotend sectie maar je vraag is voor mij veel te specific en dan ook nog over zelfbouw, valt totaal buiten mijn ervaringsgebied. Zat er aan te denken om over je vastlopers te beginnen maar deed dat niet omdat dat mogelijk te offtopic is maar imho kun je beter eerst vaststellen wat de oorzaak is van de vastlopers voordat er iets nieuws gebouwd wordt. Mijn ervaring is dat op mijn macby Frans@France - Extruder, Hotend en Filament
Re: Custom builder wanted. - 8 years ago
Maybe try this mostly (3d) printed CNC which can also be extended to be used as an 3d printerby Frans@France - General
Re: Vref instellen - 8 years ago
is afhankelijk van je stepper vandaar dat je verschillende berekeningen tegen komt. die current rating van 2.5A lijkt mij wat hoog? Dan zou je eigenlijk andere stepstick moeten gebruiken om daar optimaal gebruik van te makenby Frans@France - Electronica
Re: Heatsinkless hotend - 8 years ago
What would be the benefit of a hotend without heatsink?by Frans@France - General
Re: lead screw question - 8 years ago
Depending on the printer design the print issue could be a belt not being tightened enough and not a rod wobbleby Frans@France - General
Re: Filament sensor alternatives - 8 years ago
maybe this one is even simpler?by Frans@France - Let's design something! (I've got an idea ...)
Re: probleme reglage micro pas - 8 years ago
warning: ramps boards with bypassed jumper:by Frans@France - RepRap Groupe d'Utilisateurs Francophone
Re: Better than painters tape..... - 8 years ago
QuoteMutley3D Check out the "PrintBite" thread. Much tougher longer lasting and wider compatibility with more materials than PEI. Why would a 0.8 sheet of printbite "glued" to a underlayer with double sided tape be "much stronger, longer lasting" then a PEI? Specially when most glues will not survive x hour prints @ 110*c ?by Frans@France - General
Re: Better than painters tape..... - 8 years ago
Quoteatunguyd We have a printer at work that comes with a PEI bed - after 6 months the PEI was delaminating in some areas and had what looked like air bubbles under it. The printer company was quick to send us a replacement bed, but what I have taken from it is that PEI may not be the silver bullet it is made out to be. sounds like a thin sheet of PEI glued to something else. The PEI sheet itselby Frans@France - General
Re: Filament extruder - 8 years ago
2000 regels code verder en de user interface is zo goed als af. Moet het bewaren en ophalen van de instellingen van/naar de eeprom nog regelen. De DUE is echt een onbeleefd racemonster! Niet alleen wordt het scherm op dit moment ~8 keer per seconde gerefreshed maar tegelijkertijd lukte het om meer dan 800.000 pulsen/sec te genereren. Een aangesloten standaard stappenmotor hield er echter bij onby Frans@France - Projecten