The one I got from thingiverse compiles fineby Suggy - General
Do you know off any known problems compiling the main/lower body? S3D crashes every time I try to compile the 3 parts as it is when downloadedby Suggy - General
Order placed. but I forgot to change my delivary address, can I pm you with the correct address please?by Suggy - General
Cheers. Sorry edited before I refreshed the screenby Suggy - General
Quick question 20 or 27mm? best? and is the control board the same weather its 1 or 3?by Suggy - General
OMG you have put a lot of time into this, hat's off to you sir. And it worked a treat. Tried Tinker Cad some time ago and never got to grips with it. I use DesignSparks Mechanical and still find new stuff every time I use itby Suggy - General
I know what you mean, my paper weight is c**p aswell. and Thanks will have a shower and come backby Suggy - General
DjDemonD Only getting the refresh arrows going round and roundby Suggy - General
I have that version I use for 1 machine, 3.1.0 on 2nd machine and 3.1.1 on the 3rd. Find it easer to keep them all separate and there on 3 different pc'sby Suggy - General
Must be in a newer version than mine (1.1.0) only got Calculate Volume, Element statistics and Mesh Reductionby Suggy - General
Using S3D will have a look, thanksby Suggy - General
Iv downloaded them but there a complete print (main and top), what I am trying to say is, I have printed the clamp mount (main and top) but I would like to print just the screw mount upper part so I can try with different mounting options without printing the lower/main body again. Hope this help's to what I am asking?by Suggy - General
Guy's Much appreciate all the effort and time you have put into the project but is there any chance you can upload the printed parts separately ? ie Hot end clamp 25mm Hot end clamp 26.5mm Upper part screw mount Upper part clamp mount That way there is no need to print all the part's again if the censor is swapped to machine that requires a different mount!by Suggy - General
You could sell them as a build it yourself kit even the board, just sell all the components, I would imagine anyone that can make a 3d printer can use a soldering iron. Just a thoughtby Suggy - General
Ok thanks. Building one out of your kit is not beyond my capabilities. It's going on a e3d v6 on a printer I am building. Count me in for 1 when there ready so I don't miss out. You should put a pre-order button on your website? Cheers Ianby Suggy - General
Still Sold out Any idea when new stock will be in?by Suggy - General
Hi thanks for the info. I will bear the mks sBase from you when I have come to a decision. How are you getting on with the Lerdge?by Suggy - Smoothie
Ed Would, Managed to get a mk2a bed 300x200mm amended the settings to #define X_MIN_POS 0 #define Y_MIN_POS 0 #define Z_MIN_POS 0 #define X_MAX_POS 281.5 #define Y_MAX_POS 157 #define Z_MAX_POS 248 limited by the extruder movement #define BED_CENTER_AT_140.75_78.5 in S3D Build volume X 281.5 Y 157.0 Z 246 Origin Offset X 140.75 Y 78.5 Z 0.0 Still went to the rear right to start print, but aby Suggy - Firmware - Marlin
MKS did the Gen which ran on Marlin but the S-Base and Robins run on smoothiewareby Suggy - Smoothie
Looking to replace ramps 1.4 to MKS s-base or Robins both with a 3.2 screen or Evan the new Lerdge board that as just started to come on the market. Looking for pros and cons please. Cannot decide which one to go with any input much appriciatedby Suggy - Smoothie
I have 2 xbox360 power supply's running on a ramps with M80 to turn both supply on and M81 will turn both supply off and only level 5v turned on to keep the screen lit. M81 will shut power off every thing except 5v or is it 3.3v can't remember from the top off my headby Suggy - Firmware - Marlin
Hi All I want the print cooling fan to stay on for a set amount of time after the print as finished. I know it's M107 ? followed by the time eather in seconds or milliseconds but I cannot for the life in me what it is Could some one please refresh my memory please? Also is there anyway of putting the Power On/Off on the screen with the Info Screen Prepare Control SD card Page. My G-Codby Suggy - Firmware - Marlin
Hi Ed Would Tried your suggestion and its still the same, but thanks for the help anywayby Suggy - Firmware - Marlin
Thanks for the reply, at the moment I have a standard 210x210 mk2 hbp, I intend on making it bigger but it will have to be custom made which bumps the price up, funds are limited at the moment due to bean of work ill for 8 weeks and being self-employed done get any sick pay. I will try your suggestions when I get time and let you know the outcome. Once again thanks for the help much appreciatedby Suggy - Firmware - Marlin
When all Axis are homed the extruder is to the rear right. I have attached a diagram, this may help with the following! Line 608 #define X_MIN_POS -46 Which is 46mm to the right of the bed Line 609 #define Y_MIN_POS 0 Which is all the way to the rear Line 610 #define Z_MIN_POS 0 Which is all the way to the top Line 611 #deby Suggy - Firmware - Marlin
Ok thanks for the reply. I hade M140 & M190 M104 & M109 S3D stets the temp so I don't have to keep changing the Stemp in the script ! If I remove G1 X106 Y75 Z0 from the scrip it just goes to the rear right of the bed Line 608 #define X_MIN_POS -46 ? Because the print nozzle when homed is 46mm away from the bed Also if I use M109 S60 the printer don't turn on and I get Heating faileby Suggy - Firmware - Marlin
Ok thanks I'm using S3D 3.1.0 do you know where I need to enter the settings? Do I enter them in Global G-Code Offsets?by Suggy - Firmware - Marlin