If you have set the probe to nozzle offsets correctly, the firmware should limit the X max movement automatically. See in configuration.h Quote/** * Z Probe to nozzle (X,Y) offset, relative to (0, 0). * * In the following example the X and Y offsets are both positive: * * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } * * +-- BACK ---+ * | | * L | (+) P | R <by obewan - Reprappers
G33: Measure/List/Adjust Distortion Matrix (Repetier - Redeem) Usage G33 G33 Lnnn G33 Rnnn G33 Xnnn Ynnn Znnn Parameters L0 List distortion matrix in a report R0 Reset distortion matrix X Y Z Set correction for nearest pointby obewan - Repetier
Marlin has allways set the Z default max feedrate far to high in my opinion. Default_Max_Feedrate from 500,500,100,25 to 500,500,10,25 Your on the right track here, Try setting the Z feedrate to 2 or possibly 3 The accellration should be ok at 50.by obewan - Firmware - Marlin
You have infil speed set to auto atm,try setting it to something like 60mm/s, maybe auto is slowing it down for some unknown reason.by obewan - Slic3r
Easiest way to reverse a motor direction is rotate the connector plug 180 degreesby obewan - Firmware - Marlin
One thing i noticed in your config #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.1 // Z offset: -below +above In marlin firmware this should be a negative value for a inductive probe , as the probe trigger point is below the nozzle.by obewan - Reprappers
Really you need a sensor with at least 8mm detection range for aluminium,2 mm is just too small.by obewan - Reprappers
Try lowering the X and Y max feedrate( which i believe G0 moves at) in config.h / eepromby obewan - Firmware - Marlin
Have you sent M502 and M500 to update the values in the eeprom ?by obewan - Firmware - Marlin
I think you need to un comment these lines . #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) //#define PROBE_PT_1_X 15 //#define PROBE_PT_1_Y 180 //#define PROBE_PT_2_X 15 //#define PROBE_PT_2_Y 20 //#define PROBE_PT_3_X 170 //#define PROBE_PT_3_Y 20 #endifby obewan - Firmware - Marlin
most likly is the max Z feedrate is set too high check for this line in config.h #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } change the 5 to a 2 or 3by obewan - Prusa i3 and variants
What firmware does your printer use ?by obewan - Repetier
with marlin fm M502 ; read values from config M500 ; store values into eepromby obewan - Reprappers
If you are changing the steps/mm in the configuration.h make sure you also update the values stored in the eepromby obewan - Firmware - Marlin
Try adding a G90 ;absolute postioning to you machine start code ,maybe it is only moving up 0.3 mm if in relative mode.by obewan - Firmware - Marlin
After re flashing, you must issue a M502 and M500 to update the eeprom values with the new values from the configuration.h eeprom allways has preference over the config.h file.by obewan - Firmware - Marlin
Prussa I3 frame is for a 220x220 bed with 209mm hole spacing heres oneby obewan - Prusa i3 and variants
You could print via a host like Repetier host, that has a feedrate scroll bar that you can use on the fly.by obewan - General
Cura and repetier host both reprt the stl as not watertight. Cura seems to slice it ok Slic3r prussa edition slices ok. dammed if i can get Slic3r to work tho.by obewan - Slic3r
#define Z_PROBE_OFFSET_FROM_EXTRUDER 2.6 // Z offset: -below +above This should be a negative value as the probes 'trigger' point will be below the nozzle.by obewan - Firmware - Marlin
If the T motor is getting hotter than the others, maybe the drive current is set too high which could cause the driver to over heat and shut down for a moment.by obewan - Prusa i3 and variants
Try with M280 P0 Sxxxby obewan - Firmware - Marlin
Look at coasting In cura,does very similar.by obewan - General
0,0 is home coordinates(front left of the bed) that have a measured Z offset of -0.011 with X across the top and Y down the leftby obewan - Firmware - Marlin
If the slic3r 'start' gcode (1st image above)does not contain any entries for M104,M140,M109,M190 then slic3r (or cura) will add them to the start of your slice'd g-code automatically.by obewan - Repetier
If you are using the Repetier online config tool, half way down on the 'tools'tab, there is an option to enable 'heated bed'by obewan - Prusa i3 and variants
Where is the z switch located ,top or bottom of ? Make sure it is plugged into the corresponding monthly or max conector.by obewan - Reprappers
afaik there is only the option for dual X axis atm.by obewan - Repetier