Show all posts by user

Re: RADDS work now stable with RepRap Firmware - 6 years ago

eh sorry dc42, but I can't seem to find it on google, is it possibly to direct link me to it? The 1.21RC release, thank you very much.

by iamthebest22 - Controllers

Re: RADDS work now stable with RepRap Firmware - 6 years ago

Oh no problem, just wondering if anyone here knows cause I can't seem to find stuff about it. Great I'll download it then!

by iamthebest22 - Controllers

Re: RADDS work now stable with RepRap Firmware - 6 years ago

Hi dc42, been interested in getting a RADDS to have a backup to my two duet wifis (I really like interchangeable stepper driver boards). I just have a question about BLtouch using Reprapfirmware on RADDS, I see in here people talk about putting it on PWM 3 or PWM 1 (the lower left corner on the board where one needs to solder in the header pins). Which one is it or does it not matter, it's just

by iamthebest22 - Controllers

Re: Print Problem on two printers - 6 years ago

Another try, had a small missing layer, and top still... Is it still underextruding? I'm at 100% already though...

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

So close.... Is it still underextruding?

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Thank you MCCarman, sorry that was just a rant, because I have 7 printers in total, and all of them came with a problem that took me a a dozen hours to fix, but this one is about to overtake them all xD. I can tell you with confidence that I have tried without retraction, and then it prints fine, just lots of stringing and blobs then and a little "overextrusion" on those currently "underextrusion

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

id another test, the only settings changed were from outside in to inside out printing, retraction to 5.5mm, retraction distance 45mm/s, multiplier 0.92, temp at 185 still, and checked Only retract when crossing open spaces. I'm literally on the verge of crying/pulling my hair out, $600 machine and can't print... T_T always the same layers... (oh and also adjust printing speed for layers below in

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Alright here are the newest results, it's still the same layers, just a little better, however what I notice is this. During these problem parts, the Titan would "click" and I'd see the filament snap, which means it's being pulled too far that it snaps back and gear loses slip on filament I believe, which means I guess I can't use that high retraction distance? Should I turn on only retract on op

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Okay sorry for late notice, my parents had a small car accident, they are fine but car is totaled. Anyways, First thing I did was recalibrate the titan extruder, it was doing 10.78 on 10mm, so now it's at 9.96mm to 9.98mm. Here is the newest settings I've followed as you said MCCarman, and the picture results are also in the same folder, still the same problems at the same area.

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Thanks MCCarman, I will test it when i get home from work today again xD

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Hi all, okay finally had time to take the pictures, here are all the settings in S3D., I have put them into my dropbox folder. Thank you very much.

by iamthebest22 - Printing

Re: Print Problem on two printers - 6 years ago

Hi MCcarman, I've attached my fff files in my first post, but I'll take pictures of my settings and post it up here since I realize not everyone have S3D after I get home from work (at work now). I can say real quick I'm using Zyltech PLA, - Temp 210 all the way, -Extrusion Width 0.40mm, - Retraction settings is 4.00 mm retraction, 0.05 retration vertical Lift, 80mm/s REtraction speed -printing

by iamthebest22 - Printing

Print Problem on two printers - 6 years ago

Hi all, I am a long time fan of 3d printers, though I didn't get into the hobby until almost 1 year ago , now I am the proud owners of 7 different FDM 3d printers. I have had to solve many problems along the way and thus have learned alot. However recently two issues popped up that I just cannot for the life of me figure it out, I have spend at least 40+ hours on these issues, but just cannot fig

by iamthebest22 - Printing