Show all posts by user
(RepRap en Français)
Merci pour ta réponse,
j'aurais quand même pensé que deux machines de ce type, (config delta, extracteur bowden) auraient à peu près les mêmes "limites", et que quelqu'un qui a aussi une rostock pourrait un peu m'avancer dans cette quête.
by
tchitchou
-
RepRap Groupe d'Utilisateurs Francophone
Chers tous, bonjour,
je commence à imprimer des trucs, avec une rostock chinoise, donc, ça va pas mal, juste des fois, je crois que l'alim lâchouille, la connexion tombe, mais une nouvelle et plus puissante alim devrait régler ça.
Quand je slice, effrayé par le temps d'impression, je rajoute 10 mm/s ici et là, puis 20 etc.
Plutôt que de continuer à monter jusqu'à avoir des catastrophes, je pré
by
tchitchou
-
RepRap Groupe d'Utilisateurs Francophone
Salut,
Il y a aussi un plugin qui doit faire du Gccode pour sketchup, mais je n'ai jamais réussi a aller jusqu'à un usinage correct.
Si tu arrives à un dxf correct, donne sa chance à heekscnc, gratuit, simple, permet en plus faire des contournages, des poches, des réserves, etc.
Et.. souvent, les galères viennent des dxf qui ne sont pas aussi parfaits que ce qu'on peutcroire. (y'a plein de ve
by
tchitchou
-
RepRap Groupe d'Utilisateurs Francophone
I did the same thing once, but the extruder is so small, I think the measure is far below reality. (in my case, it was)
To be sure, you can cut a piece of PLA and push (just with the hand) against the nozzle. (by the extérior)
You'll see if it melts.
by
tchitchou
-
Prusa i3 and variants
Hi !
Can we get an image of the connections ?
by
tchitchou
-
General
Hi !
A last message, I found it !
I looked a lot of rostocks on chinese sites, contacted sellers, downloaded a lot of files.. And among the PDF, I found my board !
I still don't know the name, but there is the wiring, and the firmware
I have now the little problems of anybody who begin with a 3d printer
Here is the link, may be someone will need it, as I did.
chinese rostock package
Thank
by
tchitchou
-
General
Sorry if I insist, but..
Quotetchitchou
Quotebillober33974
Is the big chip on the board a ATmega2560?
Yep !
Can the board be a sanguino, then ?
by
tchitchou
-
General
Ok.
Tried too, same error message.
I've tried to make a search in my folders, "*recipe*.*", not a thing..
by
tchitchou
-
General
Hi,
you can try adding a long cylinder to your design (you'll cut it with a saw at the end).
The cylinder will guide the drill up to the part of the hole you want to be perfect.
by
tchitchou
-
General
QuoteOhmarinus
Just to be sure, did you select it in the tools > boards list?
I think the ATmega644 is the correct one btw.
Yep. Since the biginning.
And I see the 3 sanguino boards, now, with the arduino 1.6.0 ( plus the 0023r3 version in the good folder)
Just tried again with the ATmega644 and I have this error message :
"Third-party platform.txt does not define compiler.path. Please
by
tchitchou
-
General
QuoteOhmarinus
I downloaded the package that the seller sent you. I said this before, there is a map Sanguino in there, probably or a good reason. I'm not sure if I'm just being ignored but it's all there and I'm pretty convinced that your board will work as a sanguino.
I tried, but I don't see any sanguino card in the cards list. (in the portable arduino from the link)
I don't know why, but it'
by
tchitchou
-
General
Hi, Zavashier, I know the french forum, that's were I saw you before.
But, ok, let's continue in english. (c'est juste que je suis plus à l'aise sur le vocabulaire en français)
The firmware I have has the same lines (// 6 = Sanguinololu < 1.2 // 62 = Sanguinololu 1.2 and above).
But I can't (don't know, in fact) how to put it in the card, when I try, I have this error message :
" error:
by
tchitchou
-
General
Salut, Zavashier, rien non plus sous les stepsticks, je sais, c'est bizarre, mais c'est le cas.
Est-ce que j'ai besoin de savoir quelle carte c'est ? Je ne suis pas sûr, j'avoue.
C'est sûr que si le le firmware (pour la ramps) "passe", que le lecteur de carte et l'afficheurs fonctionnent, je me dis que ça pourraît finir par fonctionner et que tout ce qu'il me manque, c'est la reconnaissance ou a
by
tchitchou
-
General
Hi !
Quoteiamdarkyoshi I just wanted to see if there are any regulatory markings on the pcb (such as a date code, revision number, ect)
Good idea, but
unfortunately, not a thing.
(both sides) The board have many outputs, 3 strong (with radiators) (V1,V2, V3), 3 fans outputs (fan1, fan2, fan3), 1 servo, 5 drivers.
And 3 inputs for temperature, and 3 stopends.
The seller still doesn't respond, s
by
tchitchou
-
General
Thanks for the tip
Done.
gives
and
gives
.. and I have only 3 endstops on the device..
by
tchitchou
-
General
Here is a better picture ;
by
tchitchou
-
General
Hi !
Thanks you all for your time.
To Ohmarinus , here is the link to download the package ==>
The firmware have the good geometry (dimensions) for my rostock, the LCD works fine , but I suspect a problem with the pins wiring, because
- when I clic "Home" in Repetier, the first motor turns, and try to turn, even when hit the endstop.
(the endstop is ok, I've check with a multimeter, and a
by
tchitchou
-
General
I know, we have a burlesque discussion for a month now, me telling it's not a ramps 1.4, and it's not working, and him telling it is.
And no more response from him since 10 days.
So, here I am.
by
tchitchou
-
General
Quotebillober33974
Is the big chip on the board a ATmega2560?
Yep !
by
tchitchou
-
General
Yes, I have a website, and a link, I donwloaded a package, firmware, driver, softwares, assembly instructions, etc.
Assembling was ok, but the board isn't the same as the PDF..
Driver worked..
Upload firmware, ok..
But
I wired the fan on "fan1" connection, but when I switch on the fan in Repetier, it's the heat bed that heats...
I suspect same problems with the endstops..
And the seller no lo
by
tchitchou
-
General
Hi !
I don't want to replace it, I would want to use it, but with a standard marlin firmware, I have trouble to make it work, the connections are not correct.
I'm just looking for the right firmware for this board.
by
tchitchou
-
General
Hi !
Thanks, close, but not the one, mine has 5 stands for drivers, 2 slots for a SD card board..
It comes with a chinese rostock mini pro, and I have trouble to find the good wirings for the fans, heat bed, extruder etc..
by
tchitchou
-
General
Hi all !
I have this board, but I don't know exactly the reference..
And of course, I need it to make the printer work..
If someone recognises it ?
Thanks
by
tchitchou
-
General