Show all posts by user
(RepRap en Français)
Page 2 of 4
Pages: 1234
Results 31 — 60 of 103
No support, I hope so this speed no miss steps, I really would like like to speed it up but keep it like this the time of measurement (I'm not sure about the DRV8825)
by
jackantubis
-
CoreXY Machines
To the digital dentist:
I'm already working on this kind of measurent :-) your thought call me ;-).
I will try too to make measurement with manual pisitionning of the motor: 1 full manual rotation of the motor -> 1 measure of the position of the bed (to completely remove the uncertainty of the motor driver.
Yes the volcano is hard to seting up :-( still working on the PID and extrusion rat
by
jackantubis
-
CoreXY Machines
Une courroie fait la liaison entre le moteur et les 2 vis à billes, 10mm de large par 1m30 de long.
le seul jeu qui pourrait être possible et en bas car les vis à billes sont posées sur le roulement inférieur et compressées par le poids du lit chauffant (plus de 2kg) donc difficile de croire que àa peut bouger ici mais tout est possible :-). les vis à billes ont un écrou anti jeu très efficace.
L
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
Si vous regardez le photos de la machine je n'ai pas de coupleurs, les vis à billes sont sur un roulement avec une rondelle acier entre les deux et les tout monté sur un support imprimé à 100% d'infill et sur 2 extrusions 2020, difficile de faire plus répétable !!
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
the other standard leadscrews (8mm pitch and 1.5mm pitch) are without anti-backlash nut, with the same issue.
Test with 10mm belt:
by
jackantubis
-
CoreXY Machines
the Z rails are smooth as possible don't feel something when I move by hand :-(
Don't understand the difference between bottom and the rest of the part. yesterday I checked the quality at the begenning of the print and 10 hours later bad result !! frustrating :-O !!
Now I installed 10mm belt, test ongoing
by
jackantubis
-
CoreXY Machines
No same length, it was planning to use 3 leadscrews with this belt, I designed the new linear Z a week after the order, a new shorter one is planed later.
by
jackantubis
-
CoreXY Machines
Tu veux dire avoir un roulement à bille au dessus et en dessous de la poulie pour ne pas avoir d'effort latéral sur la vis à bille ?
j'y ai pensé mais la vis à bille est un peut courte pour ça, je vais essayer de redessiner le support inférieur pour intégrer un autre roulement au dessus de la poulie, surtout que je viens de recevoir une courroie de 10MM en GT2 à la place de la 6MM pour mettre pl
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
I received today my 10mm GT2 closed belt and 10mm pulleys instead of the 6mm one, I'll check ASAP if the tension is better and the flexibility lower, to increase the linearity cheched with the comparator
by
jackantubis
-
CoreXY Machines
Gearing, 20 on motor, 60 on leadscrews, pitch 4mm, prusa calculator told me 0,18mm optimal layer but I can try 0,2mm. Thin calibration is done on this print, 0.4mm nozzle -> around 0.4mm wall
by
jackantubis
-
CoreXY Machines
On the left of the picture 0.4mm nozzle layer height 0.18mm, cura, spiral vase
On the video with comparator, 100 microns movement ask by software, the linearity is quite good repetability too but could be better
by
jackantubis
-
CoreXY Machines
Sur la photo à gauche buse 0.4mm hauteur de couche de 0.18mm sous cura en spiral vase
Test au comparateur, mouvement de 100 microns demandé par le soft. La linéarité est pas mal la répétabilité aussi mais peut mieux faire
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
God idea for stepper wires, layer height too, usually I use 0.2mm minimum with 0.6 nozzle bit prusa calculator give me 0.18, I'll try with smaller nozzle or bigger layer.
by
jackantubis
-
CoreXY Machines
ballscrews + vase mode, cura or slic3r same result, 0.6 mm nozzle 0.18mm layer height
by
jackantubis
-
CoreXY Machines
Tout semble tourner rond, je suis passé avec des vis à billes, c'est un peu mieux mais toujours du wobble, je continue de chercher.
Ici hauteur de couche 0.18mm, cura et slic3r même résultat mais mieux sur le Z
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
Already tried without heatbed same result, for vase mode same result.
I changed my leadscrews for balscrews it's better but wobble is still here just lower (not the same occurrence in Z because different pitch)
by
jackantubis
-
CoreXY Machines
OK I follow you on your Z axis setup on your specific post.
Your design inspire me for mine ;-) thanks
This banding issue is a crap
I'll try soon ballscrews with the same setup. later I'll design Z belt design to test all of this but without worm gear !
Same as you I tried a lot of things to find the issue and isolate it !! I'll ty some of your test on my setup to find the GOLD setting :-)
by
jackantubis
-
CoreXY Machines
1) all the size :-): pictures 0.4mm
2)all layer thikness: I tried a lot of different layer thikness, reprap prusa calculator told me 0.18mm don't really change anyting
3) speed here 60mm/s, tried 50mm/s and lower and higher but same result
4)Yes DRV8825 :-( ordered diode smoother just to try if it improve Z
5) I tried 1 motor and 2 motors to increase the torque. rifht current for 1 motor 1.
by
jackantubis
-
CoreXY Machines
Maybe the leadscrews but good supplyer (https://www.motedis.fr/shop/index.php)
by
jackantubis
-
CoreXY Machines
no play in linear rails, I can move the bed with strong pressure front, the link between bed and linear rail is printed (I'll mill this part in alluminium soon) but I already have this issue with 3 leadscrews and wheells instead of linear rails :-(
I changed the belt tensionner no change :-(
by
jackantubis
-
CoreXY Machines
Je connais le wobble sur prusa, j'en ai une, mais c'est surtout avec des vis normales, pas avec des vis trapézoïdales.
Un pote calé en mécanique m'a dit que la courroie était peu être trop souple donc j'en ai une meilleure en commande pour voir.
Ça fait chier d'avoir une bonne machine avec un problème basique qui vient de on ne sait pas où :-(
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
Hi everybody,
I have a impossible wobble!!
My mechanic seems good but still have wobble.
With a comparator mounted on the carriage I can see the default but can't find it.
My config:
MKS Sbase 1.3 16 micro steps, 20 teeth pulley on the motor, 60 teeth on the leadscrews, 1.5mm pitch leadscrews, gt2 belt.
The motor current is ok,
I tried different motors,
I tried 2 motors at same time with cur
by
jackantubis
-
CoreXY Machines
Salut à tous,
Depuis un moment j'ai un wobble que j'arrive pas en enlever malgré ma config plutôt propre mécaniquement.
J'ai une MKS Sbase 1.3 en 16 micro steps, une poulie de 20 dents sur le moteur, 60 dents sur les vis Trap, vis Trap avec un pas de 1,5mm, courroie en GT2.
Au comparateur monté sur la support de tête, je constate bien un défaut de wobble, la calibration du Z reste bonne.
Les co
by
jackantubis
-
RepRap Groupe d'Utilisateurs Francophone
Yes too much corner are useless, I'm looking for a design with 4040 extrusion, actually my D-bot is on 2040 and shake a bit maybe upgrade to 4040
by
jackantubis
-
CoreXY Machines
Hi, add some bottom space for electronics I forgot this on mine :-(
I found this picture on the web close to your design with space bottom
by
jackantubis
-
CoreXY Machines
Page 2 of 4
Pages: 1234