Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 17 of 17
Ok. Update.
If I make the G-Code inside the host application I get the error, but if I make the G-Code in Slic3r and open the file with repetier it prints fine.
I am using the calibration 0.5mm-thin-wall.stl STL LINK
by
Fabiano
-
Repetier
Hi.
I have an issue with the Repetier 0.18 Host for Mac.
The machine seems to work perfectly moving the axis, extruder etc., but when I send it to print it moves to position normally and then it makes more noise then move the motors. I recorded a video of the problem. You can just hear high pitch noise in the background.
MOV
I reinstalled version 0.17 and 0.16 and they work fine.
OSX Lion (al
by
Fabiano
-
Repetier
Gilberto.
Pois é. Eles finalmente me responderam e o preço deles é R$275/kg de PLA....
Achei um site argentino que vende ABS e ABS PC. O preço é de AR$150/kg, algo em torno de R$70/kg.
Encomendei 3Kg, vou testa-los e posto aqui o resultado.
Abraço.
F.
by
Fabiano
-
Brazil, São Paulo RUG
So should I keep both dummies, one on the 12V and one on the 5V, or just the one on 5V?
F.
by
Fabiano
-
Repetier
Hello.
When I bought my machine parts I was asked the same question 3mm or 1.75mm and 0.34 or 0.5mm nozzle. I opted for 3mm and for the 0.34mm nozzle.
My machine is now 95% ready and I was wondering does the fact that I ordered parts for a 3mm extruder means I can print ONLY print with 3mm or can I print using both filaments sizes?
Thanks in advance.
F.
by
Fabiano
-
Plastic Extruder Working Group
Thanks everybody for the help. Really appreciate it.
Its hard to figure things out when you never even seen the machine in person.
After all it was just a question of wiring back inside the PSU. The dummy is not required to run the machine (at least in my case), but it helped me get to the problem and learn a few more things about how all of this works.
Now I need to work on the extruder block
by
Fabiano
-
Repetier
Nophead.
I just managed to fix the pulsing light and I was able to turn the 6.8Ohms Extruder Heater.
I did a quick run (without filament) but with all motors on and the result was good....well, sort of.
The Heat Resistor immediately starting to smoke and turn black.
Is it something to do with the power supply of is my wiring wrong, etc...
Thanks again.
F.
by
Fabiano
-
Repetier
Hello to all.
After insulting myself and the power supply several times I did the dummy connections on the red/black yellow/black cables using a 12V car lamp.
The weird thing is, and probably the one and only problem after all, it that both lamps are pulsing.
I saw in another post someone with the exact same problem and nophead said something about connection red to black wires, etc. Again, I a
by
Fabiano
-
Repetier
Repetier.
Ok I will try that and give you a reply in a few hours...
One more thing before I go. IF the problem is the Amps what If I take X, Y and Z motors and the OPTOS, leaving just the Extruder Parts connected to the board, my 10A@12V should be able to run the Heater. Correct?
I just tried that and it does the same thing LED 3 Flashes once and Conneciton Lost.
Thanks in advance again.
F.
by
Fabiano
-
Repetier
Repetier.
Bingo. Re-wired and its working.
Thanks again.
F.
by
Fabiano
-
Repetier
Nophead.
I am not very knowledgeable on electronics, so I didn't quite get your reply...sorry.
My PSU is connected to the Gen6 via a single set of yellow/black wires. Nothing else is attached to it.
Here is an IMAGE of the ATX-Gen6 connection
Any advise is appreciated.
F.
by
Fabiano
-
Repetier
Hello again.
I just changed the Extruder_Speed from 20.0 to 18.0 and to 10.0 and it does the exact same movement. I have uploaded a video of the problem. Notice how the extruder kind of moves forward and then backwards when I hit Extrude:
Extruder Problem (MOV)
Also about the Amps on the ATX. It says 10A for the +12V, everything else is lower then this value.
Currently I do not have a Heated
by
Fabiano
-
Repetier
Repetier.
After trying your suggestions this is the outcome:
Dry Run with NO motors connected:
I did 5 runs and it worked 100% of the time.
Dry Run with ONLY the X, Y and Z motors connected:
It did not work at first, same problem as before (connection closed).
Then I found something out if I run the motors once, even 0.1mm, just to switch them on then turn them off and press FAKE OK, I can mak
by
Fabiano
-
Repetier
Hi.
My power supply is 12V but max of 10Amps and my Extruder Heat and Thermistor are these?
Extruder Heat
Thermistor
I am currently doing some tests and I will give a feedback in 30min or so.
Thanks.
F.
by
Fabiano
-
Repetier
Thanks for the reply.
I have a felling is a power shortage as well, but I cannot figure it out.
My power supply is a brand new ATX 200W and the voltage is 12V solid.
Also all the TP1, TP2, TP3 and TP4 little dials on the board are all set on the middle.
Do you think I could increase the power input above 12V?
Also I have attached a Log file of my last run, don't know if can be of any help.
F.
by
Fabiano
-
Repetier
Hi.
I am new to reprap and just 2 days ago finished building my prusa mendel.
I am having 2 issues that are stopping me from printing anything:
1. The softwares disconects from my printer when I am trying to move a motor, sometimes is the 1st click to move 10mm and sometimes it moves all motors ok but when I sent a model for dry run it does some movement and stops. I am not able to do even a 1
by
Fabiano
-
Repetier
Tem essa empresa aqui:
Mas eles nunca retornaram minha ligação nem emails.
F.
by
Fabiano
-
Brazil, São Paulo RUG