Show all posts by user

Re: PLA/Brass Bushings - 12 years ago

HI.. About 10 hours before they ststed to show problems in the prints. Abs would wear faster, plus they would break when you tried to snap them on . Auzze Myndale Wrote: ------------------------------------------------------- > Auzze Wrote: > > As I have a working Prusa and have used the PLA > > bushing when I first built I found that they > worn > > out very quick, so

by Auzze - Australia, Melbourne RUG

Re: Current RAMPS firmware - 12 years ago

HI.. Sprinter is what I have been using, . Simply to use and understand. Auzze

by Auzze - Reprappers

Re: Stock of 3.0 and 1.75 ABS no PLA yet - but soon - 12 years ago

HI.. I would be happy with both but learning towards 3mm as it's still the standed. Would be nice to have a good slection of colours. Auzze

by Auzze - Australia, Melbourne RUG

Re: PLA/Brass Bushings - 12 years ago

HI.. As I have a working Prusa and have used the PLA bushing when I first built I found that they worn out very quick, so quick I just printed a new set before the ones in the printer failed. I now use LM8UU liner bearing I got from china. I use a 3 bearing X carriage desiged by Greg Frost, and LM8UU bearing holder for Y axis I downloaded and printed from thingverse. As for Z I use felt bushing

by Auzze - Australia, Melbourne RUG

Re: We supply PLA,ABS filaments - 12 years ago

HI.. All looks good but some pricing would be nice plus shipping to Australia. Do you have some samples so we can try it before we comit to buy large amounts. Auzze

by Auzze - Australia, Melbourne RUG

Re: RAMPS Electronics - 12 years ago

HI, E-mail sent. I'm also in Ballarat Auzze Delory Wrote: ------------------------------------------------------- > Hi Aussie. > > Do you have any other bits and pieces available > (electronics, motors, plastic componetns, > extruder, etc.)? We are interested in assembling a > Prusa, and are just starting the procurement phase > (and one of us also lives in Ballarat). C

by Auzze - Australia, Melbourne RUG

Re: RAMPS Electronics - 12 years ago

HI wayne. Where abouts in Melbourne are you. As for RAMPS, I sell a full V1.3 RAMPS kit complete with polous, endstops and SDramps. You can buy it as a kit (which you build) or fully assembled and tested. As for motors you get pickup some second hand nema 17 motor on ebay (I have the same ones on my small cnc driil mill) Auzze Ballarat

by Auzze - Australia, Melbourne RUG

Re: I sell plastic filaments - 12 years ago

I have asked for a sample to test, hope they will as I hate to buy it and it's no good. Auzze Greg Frost Wrote: ------------------------------------------------------- > Looks like very good prices. If someone gets any > of this, please post a review on the quality.

by Auzze - For Sale

[AU] Hobbed Bolts - FOR SALE - 12 years ago

HI.. I have a small supply of Hobbed Bolts for the wade extruder, each bolt comes with 2 nuts and 3 washers. (These are made on my lathe and I use them) Hobbed Bolt Cost is $10.00AU which includes postage in Australia. If interested please e-mail me @ auzzemit@gmail.com and I will get back to you with paymen

by Auzze - For Sale

Re: Hobbed Bolts - For Sale again - 12 years ago

Bump

by Auzze - Australia, Melbourne RUG

Re: It's Alive! (but what's best way to reload filiment?) - 12 years ago

HI.. If you cut the new filement squarly on the end, you can feed it on top of the one abour to run out. just wach the old one and stick it in the hole . If you are changing colour it give a great effect. Auzze

by Auzze - General Mendel Topics

Re: 3.0mm Ø ABS Extrudate Manufacturer - Melbourne - 12 years ago

HI.. Well I hate to say but the local supplier hasn't returned my phone calls or e-mail about PLA, not sure why but me think they can't supply. If you are looking for PLA, I use Vik's great PLA from NZ (http://diamondage.co.nz/pla) I few people use it plus it prints great. Sadly, we are in Melbourne. Auzze sketchyarchitect Wrote: ------------------------------------------------------- > co

by Auzze - Australia, Melbourne RUG

Re: 3.0mm Ø ABS Extrudate Manufacturer - Melbourne - 12 years ago

HI.. Just wondering what the status of the PLA is.. Looking to get some to try before I comit to a large buy. Auzze

by Auzze - Australia, Melbourne RUG

Re: 2mm walls are 2.3mm wide?? - 12 years ago

HI.. Try lowering your flow rate.. Auzze

by Auzze - General

Re: May's get togrther/BBQ - 12 years ago

HI.. Sounds good.. Shouldbe there about 1:00 as I have to drop in on my brother. Auzze

by Auzze - Australia, Melbourne RUG

Re: Prusa belt lenghts. Is the Wiki BOM correct? - 12 years ago

Greame You only need to buy 2 meter of belt and slit it down the middle. (this will then give you some spare) You can get your belt from Auzze

by Auzze - General Mendel Topics

Finshed - 12 years ago

HI.. I have upgraded my Huxley to a Huxley-Prusa and I have the parts from the old Huxley left over. (Well not lft over I replace every part) This will make a fully Huxley but comes with "NO" motors or electrics or hardware, but comes with the 3 belts needed. Asking $100.00 plus some postage If interested please PM me here. Auzze PS, the parts are GREEN

by Auzze - Australia, Melbourne RUG

Re: ABS Colours - your input please - 12 years ago

HI.. A light blue would be nice and some orange.. Auzze

by Auzze - Australia, Melbourne RUG

Re: ABS Rod - 50mtr Black and White - Available - 12 years ago

HI... I would like to try some 1.75 PLA as I made a new hotend with a .35 nozzle. Be interesting to how it runs. If the filement size doesn't get bigger than 1.95mm it should make for some very nice prints. Auzze

by Auzze - Australia, Melbourne RUG

Re: Heater stays on even when I say off (ramps, tonokip, repsnapper) - 12 years ago

HI.. In repsnapper "END" Gcode just check you have a M104 S0 this will trun off the heater once your print has finshed. If you are using SF40 to slice and dice your STL then make sure you have Turn extruder at shut down, you will find that in craft/preface at the bottom. Auzze

by Auzze - RAMPS Electronics

Re: For Sale - Complete RAMPS Setup - 12 years ago

Sold, I will have another set ready in a few weeks.. I you wish to pre-order them, please PM me. Thanks Auzze.

by Auzze - Australia, Melbourne RUG

[AU] Complete 1.2v RAMPS setup. - 12 years ago

HI.. I have for sale a complete assembled RAMPS setup, this includes Mega 1280, ramps 1.2v PCB with all parts soldered in place, 4 polous stepper boards with heat sniks, SDRamps add-on and 3 microswitch endstops. I will also be loaded with the latest "Sprinter" firmware with lets you print from an MicroSD card. This will allow you to have one of the best control system for your REpRap. Ask

by Auzze - For Sale

Finshed - 12 years ago

HI.. I have a few complete assembled RAMPS setup for sale again, this includes Mega 1280, ramps 1.3v PCB with all parts soldered in place, 5 polous stepper boards with heat sniks (M4 NUTS), SDRamps add-on (doesn't include the mircosd card), 3 microswitch endstops made up and tested and full set of plugs and terminals so you can hook up your motors (you will need to install them on your motors).

by Auzze - Australia, Melbourne RUG

Re: May's get togrther/BBQ - 12 years ago

HI We are tring to have a meeting evry 2 months but sometimes it could a little over. Auzze thaytan Wrote: ------------------------------------------------------- > I just found out my cousin's engagement party is > on the 21st, so I can't make this one after all. I > hope there'll be another soon to come and say Hi > at. > > J.

by Auzze - Australia, Melbourne RUG

Finshed - 12 years ago

HI.. I now have 4 RAMPS SD card kit with PCB and parts, as per Kliment firmware. PCB Only - $12.00. includes postage Kit including PCb and parts - $25.00 includes postage Asembled - $35.00 including postage. . If intersted please PM me here and I will get back to you. Auzze

by Auzze - Australia, Melbourne RUG

Re: May's get togrther/BBQ - 12 years ago

HI.. At the monent Saturdays are the best day for me as the wife is home Sundays now. So we are doing family stuff Auzze Cefiar Wrote: ------------------------------------------------------- > Auzze: Saturday the 21st is fine by me. I just > thought you couldn't do Saturdays usually....??

by Auzze - Australia, Melbourne RUG

Re: RAMPS sheild PCB buy in? - 12 years ago

HI.. I have a few V1.2 PCB, $15.00 each with postage. Auzze

by Auzze - Australia, Melbourne RUG

Re: May's get togrther/BBQ - 12 years ago

Cefiar Wrote: ------------------------------------------------------- > Update: Things at home are now resolved, so we're > a go for holding the meet here again. That sounds great, Thanks Cefiar Now for the date, say the Saturday the 21th of May???? Auzze

by Auzze - Australia, Melbourne RUG

It's alive and printing - 12 years ago

HI.. After a long battle my Prusa it's now working and printer stuff that I'm happy with.. This now leaves me time to fine turn the SF40 setting, then I can start on my OzBot printer. Auzze

by Auzze - Australia, Melbourne RUG

Re: Extruder Heating Resister - Technical details please - 12 years ago

HI.. try here Auzze

by Auzze - Reprappers