I use now: M569 P6 Y S1 R1 M584 Y6 T1 M569 P7 Z S1 R1 M584 Z7 T1 If i remove M569 and set only: M584 Y6 T1 M584 Z7 T1 or M584 P6 Y6 T1 M584 P7 Z7 T1 Drives not work! And clear to me please about timing. If a use TB6600 drive where i must set timing (T parametr) in M584 command or in M569 ? Thank you!by Potapich - Duet
Ok get it! Work: M569 P7 Z S1 R0 M569 P6 Y S1 R0 M584 Y6 T5 M584 Z7 T5 Is this ok? (Latest FW & TB6600 driver)by Potapich - Duet
Ok thank you! M584 Y6 T5 - working. But how to inverse enable signal? M584 Y6 T5 R1 is not working for me. It inverses and work unstable when i add M569 P6 Y S1 R1by Potapich - Duet
i use Duet 0.8.5by Potapich - Duet
I try use external drive with these commands: M569 P0 S1 ; Drive 0 goes forwards M569 P1 S0 ; Drive 1 goes backwards ; OFF M569 P2 S1 ; Drive 2 goes forwards M569 P8 Z S1 R ;E5 M569 P3 S1 ; Drive 3 goes forwards But drive connected to board still working. External drive not working. Please point me where is wrong? (M569 P8 Z0 S1 R ;E5 i also tried)by Potapich - Duet
Is Mesh bed leveling available for Duet FW? Where i can read about it? Thank you!by Potapich - Duet
Is MBL or UBL works for first layer only? Or how its work while printing?by Potapich - Firmware - Marlin
Is this only for Duet WIFI оr will work ok on my board 0.8.5 ?by Potapich - Duet
DC42 is routines for bed and for chamber heater the same? Both beds wil be work identically?by Potapich - Duet
When i try to enable in the configuration # network settings network.enable true Board stops working, lit only led D7 I try all the settings under # network settings - nothing changes. File configutation.txt normal, if i set on same SD card "network.enable false" - then all starts to work. Tried FW from MKS and the latest firmware from Smoothy. I don't know what to try now! Maybe someone kby Potapich - Controllers
I have Duet v0.85 Is there any way to add second heated bet to duet fw? Second bed must be controlled and operate independently from main heated bed. Bed will be connected to SSR. I need this for large printer and two heated zones.by Potapich - Duet
Do you think Duet FW will work on this Board?by Potapich - Controllers
Jumper is set to 5v. But display is not lit.by Potapich - Controllers
Hello. Not working board MKS Sbase! If SD card installed, it lights up only the led D7. If the SD card is not installed, it lights up the led D7 and D1. Blink the led D2 and D3. Smoothie device not appearing in device manger I tried to upgrade the FW - nothing changes, but the file on the SD card changes from firmware.bin to firmware.cur Also not working screen MKS TFT28 if it plugged into theby Potapich - Controllers
Its in Arduino library - File - Examples - EEPROM - eeprom_clear. Compile and load to board. After restart, load Marlin.by Potapich - Printing
You think this may be due to temperature? Well, I will try to reduce Thank you!by Potapich - Printing
Try clear EPROM - find programm for this in standart Arduino library. Then set 250000 speed in FW.by Potapich - Printing
How exactly said! This ABS, temperature 255 degrees, the fans are off. The bed temperature is approximately the same. If you look closely, on the second "floor", first layers corners normal, but then again starts to degrade. Please see new file.by Potapich - Printing
Greetings! There is a problem here. Do you think what might be wrong?by Potapich - Printing