Eccomi di nuovo e dato che non riesco ad editare i post precedenti iniziamo da qui! Per prima cosa una foto del display RRD SMARTCONTROLLER e del mio bellissimo ed ordinato adattatore : Spiegherò cosa serve per il corretto funzionamento per punti. Ho preso come riferimento il Marlin Firmware ma si può ottenere lo stesso risultato anche con gli altri andando ad editare i files corrispondenti a qby mignolo4 - GCODE, Software e Firmware
riservatoby mignolo4 - GCODE, Software e Firmware
Nei giorni scorsi ho avuto la necessità di provare sulla mia Delta autocostruita con board ArduinoDue+RADDS, il REPRAP_DISCOUNT_SMART_CONTROLLER, il classico display a caratteri da 20x4 anche conosciuto come LCD2004 (e presente sulla Anycubic Linear Plus per darvi un'idea) Sembra che questa combinazione (RADDS+SmartLCD) non sia stata prevista nei vari firmware (MK4Duo, Marlin e Repetier) quindiby mignolo4 - GCODE, Software e Firmware
Solved!!! Following this discussion (third page) I realised that that was my exact same problem To summarise: I have got a faulty Arduino Due Clone (reprap.me) with a wrong JR1 resistor (it should be 0 Ω ) Since the JR1 resistor affects the reference 3.3V, soldering some tin on top of that resistor (thus making a short) solve the problem! Urray :-)by mignolo4 - Repetier
Well done toxuin, I had the same issue with a DUE board bought from reprap.me. Many thanks to mandrav for his solution on third page; I love you man, it was driving me crazy!!!by mignolo4 - Controllers
Nelle ultime ore ho finalmente avuto la possibilità di rimettermi a fare un po' di prove... (molto interessante il fatto dei rumors con la lan montata...) Per prima cosa ho smontato la RADDS; ho poi misurato sulla DUE la tensione sui canali da AD0 in poi e con mia sorpresa presentano una tensione! Su alcuni ingressi ADx la tensione è 1,4V mentre su altri è quella di riferimento e cioè 3.3V Ma nby mignolo4 - Elettronica e meccanica
Grazie ragazzi, grazie Angelo (you should know quite well this board! :-) ) Ho già provato sia RepetierFirmware sia MarlinKrimbra, a cambiare termistore e canale termistore... con i medesimi risultati negativi. Appena ho tempo ripasserei le saldature (quelle più accessibili) per vedere se cambia qualcosa. Se non dovessi risolvere avrei bisogno di fare prove incrociate con altre schede, ma spendby mignolo4 - Elettronica e meccanica
Il fatto è che già ho provato altri firmware, ma ho sempre gli stessi problemi! Quindi mi fa pensare che sia un problema hardware, ma cosa? La conversione sembra funzionare bene ma i valori di tensione sono sballati (e qui invece sembrerebbe un problema software come una formula sbagliata per calcolare la temperatura): T: -3° RAW0 4044 (with 6,5KΩ and 1,89V) T: 85° RAW0 2680 (with 2,6KΩ and 1by mignolo4 - Elettronica e meccanica
Ciao ragazzi, grazie per le info che condividete con la community, mi saranno molto utili in futuro... vedo che mangiate elettronica e schemi elettrici a colazione e quindi vi chiedo gentilmente di aiutarmi con il mio problema sui termistori di una RADDS 1.5. Mi sta facendo impazzire... con le mie conoscenze limitate non riesco a capire dove sia il problema. Qui la discussione originale nella sby mignolo4 - Elettronica e meccanica
First of all, thank you very much for your reply! I've been busy in the last few days, but in the evening I tried to get to the bottom of it. - I connected a 22KΩ potentiometer on the T1 Pin (thermistor ATC Semitec 104GT2 in the firmware) To let you understand what I discovered, these are the most significant results with the M105 X0 code: T: -3° RAW0 4044 (with 6,5KΩ and 1,89V) T:by mignolo4 - Repetier
Hello guys, I need your help with the thermistor configuration! In the last two years I've built a mendelmax1.5 and now I have designed my own 3printer with ArduinoDue and RADDS. I've always checked this forum because of the huge amount of information I can find, and that always helped a lot to solve my problems. But now I'm stuck! :-( So, what's the problem? - I upload Repetier firmware (0.9by mignolo4 - Repetier