Hi, I was just wondering if anyone has made a Marlin config for the LOTMAXX SC-10?by peps1 - Firmware - Marlin
Is there a Gcode command or setting in EEPROM to remove the saved mesh? I would like to switch back to manual leveling while I wait for a new probe, without having to flash a new firmware without auto leveling.by peps1 - Repetier
QuoteVDX ... the RAPS128 have the same pinout as the other "pololu-like" drivers - only the polarity of the enable-pin has to be inverted in the firmware ... Thanks, VDX, I get the RAPS128 will work, I just wondering what my other options would be on the RADDS board?by peps1 - Controllers
Hello, looking to switch out my DRV8825 drivers, but the RADDS manual only states support for RAPS128 Drivers as an upgrade. Are there any other drivers like the TMC2208 that will work with RADDS that don't require lots of mods to the boards wiring? Thank you for taking the time to read.by peps1 - Controllers
Hi, I was wondering if someone much smarter could help me? I want to test out some probes, but Repetier Firmware does not have a M48 Probe repeatability test as found in Marlin. Could someone help me out with working out how to do this with G code in Repetier? (ideally, I want to just probe the same spot 50 times in a row and record the deviation).by peps1 - Repetier
Solved, was a faulty driver chip!by peps1 - Controllers
Hi, I have a "Full Graphic Smart Controller" for my RAMPS 1.4 board and am having a strange issue that when I power it on the screen goes from full brightness to being to faint to read after a couple of seconds. It will also go to full brightness when flashing the firmware. Is this a Known issue? Any fix? (Repetier-Firmware version 1.0.2)by peps1 - Controllers
QuoteLB How did you solve it? What kind of probe did you hook up? Used a BLTouch sensor and this guide:by peps1 - Controllers
Changed mount for my probe, and would like to lower the Z axis lower than the current home, so I can move the hotend to the right level (will be -2/3mm from what currently set as the offset for the probe).by peps1 - Firmware - mainstream and related support
OK, wired up an extra 5v to the servo and set servo pin to digital pin 5. Can now run all the commands Pin-UP, Pin-Down, SelfTest and so on. But when I home the Z or run the auto level via the UI, the BLTouch will trigger, lift up, repeat......then nosedive through the bed! (when doing the auto level it also totally ignores the offset?)by peps1 - Repetier
No joy, BLTouch just not lighting up or reacting to any Gcode. Have it wire in like this, but without the additional servo +5v as I read you only need that when you have light but not the amps to trigger the pin @obewan did you have to use the servo +5v? (and what should the servo pin be set too? right now its digital pin 11).by peps1 - Repetier
Solved the firmware issue, had totally forgotten I had upgraded stepper drivers on this printer and the config.h did not reflect that, so now I have a working 1.0.2 firmware without probe, will make the changes and see if I can get probe working!by peps1 - Repetier
Quoteobewan Try just selecting one language so it defaults to it. I see you have selected generic therimstor table 1, have you created your own table for this ? better to select one of the pre set thermistors for bed and extruder. Changed them to 104GT-2 for the hotend and NTC 100K for the bed Hotend I'm using this: Bed I'm using this: Still having the same issues where I can move anythinby peps1 - Repetier
I have a 0.92.3 build of Repetier that has been working fine for ages, but recently got a probe, and wanted to upgrade to 1.0.2. I left everything the same apart from the setting related to the probe, downloaded the firmware, unzipped and flashed, only to be greeted by the Choose language screen, then the home screen showing the wrong temps 7° (its should about 24°+) and if I try and home XY orby peps1 - Controllers
uggggg......having no luck with this firmware update with the added probe, when my printer loads up it just asks me the language then shows me the home screen with the bed and hot end at 7° (its should about 24°) and if I try and home XY or Z it just hangs on Homing..... ***Please Wait*** and nothing happens Could really do with some help here. Edit to add: Just check and took my old firmwareby peps1 - Repetier
Quoteobewan You still need to set the X and Y offsets for the probe position in relation to the nozzle otherwise the firmware can not compensate for probing positions. Is the prone in front or behind the nozzle, and how many mm ? Is the probe to the left or the right of the nozzle and how many mm ? Moved the nozzle to a spot on the bed and got: X= 111.40 Y= 80.00 Z= 0.00 And moved the tip of thby peps1 - Repetier
Has anyone come across a idiots guide to adding UI commands? Just want to be able to add some simple Gcode pushes, like adding an option to send M340 P0 S2200 to reset a probe via the LCD.by peps1 - Repetier
Would it be possible for someone to double check my configuration? Can't seem to find the options for: Pre raise Z axis Pre raise Distance Min. Homing Temperature XY Homing pos. for Z Ignore above missing options, was not in Repetier-Firmware configuration tool for version 1.0.2 So here is my Config setting so far: Could also do with a hand with the offsets as my carriage is 220x220mm,by peps1 - Repetier
Thanks obewan, Will Print a mount and adjust the firmware! Sure I will have more question when it all mountedby peps1 - Repetier
Thanks, uploaded my current Configuration.h and followed your images, what should I put in for probs X Y offsets? also seem to be missing: Min. Homing Temperature XY Homing pos. for Z Also, have a huge number of new "I'm a new option!" available, not sure what one I need and dont....ummm...here is the list if anyone wants to help!? General Keep Alive Interval (set at 2000) Z-correction (diby peps1 - Repetier
Hello guys and girls. Has anyone got a mechanical probe like the BLTouch working with Repetier? interested in adding a probe to my old Di3 but a quick google seems to be telling me its a bit of a nightmare on Repetier over Marlin. I have been out of FDM printing for a while, playing with DLP, but want to get back into printing larger mechanical parts on my old but faithful Duplicator i3 I haveby peps1 - Repetier
You are 100% correct, had not updated the EEPROM from the old values! (any other values I should change while I'm here?)by peps1 - Controllers
I have switched from A4988 drivers to DRV8825, but am having a little trouble. After setting the axis steps to use 1/32 micro steps (doubling their value for the 1/16 setting), and set the VREF to 0.65VDC for my 1.3Amp motors (VREF = I_TripMax / 2) My M0, M1, M2 pins are all at 3.3VDC, and jumpers all set for 1/32 steps. I have a strange problem where my axis will only travel half the distanby peps1 - Controllers
Yes, with a new Due, everything seems be be behaving as it should Thank you for your helpby peps1 - Controllers
Switched out the Due for another one, and now get 4.61V under USB, and a much more respectable 5.08V when powered by the printers PSU. As expected this also resolves the flicking on the LED, and having to adjust the contrast when powering over USB vs PSU. Will double check the voltage stays stable when printing, just in case!by peps1 - Controllers
OK here are the quite worrying voltage reading from the 5V pad..... Just USB power to the Due = 4.53V USB + 12V PSU = 7.15V Heating Bed = ~6.7V Heating Bed + Hotend = ~6.4V Printing= ~5,8V And here is how I have my printer setup:by peps1 - Controllers
Sure, Is it OK to read the voltages from the Aux1 pads, as they look like they are going to be the easiest to get to?by peps1 - Controllers
QuoteVDX ... the USB-connector can only handle 5V! - it's direct connected to the 5V-circuitry, so higher voltages will damage some of the chips. Yes, I understand the USB is 5V and the Due runs on 3.3V, I was wondering if you were suggesting ALSO powering it from the 2.1mm jack that will take 7-12V power supply. QuoteVDXIit seems, your 12V PSU is not strong enough to drive the motors and supby peps1 - Controllers
Thanks Viktor & DC42by peps1 - Controllers