Show all posts by user
Have you tried bolting a dremel or router to your RepRap? Can you engrave and drill PCBs? Or cut wood, or ... steel? (Or do you have a commercial mill or CNC router?)
Re: MKS Gen L problems. - 2 years ago
Follow this Link I have also used MKS with my 5 extruder controller #define MOTHERBOARD BOARD_RAMPS_14_EFB //#define MOTHERBOARD BOARD_MKS_BASE_14 Post your configuration.h fileby Roberts_Clif - Firmware - Marlin
Re: MarlinTarantula-EasyConfig-1.1.x wrong extruder fan - 2 years ago
Here is where extruder E1 is configured to a Fan. Configuration.h #define MOTHERBOARD BOARD_MKS_GEN_13 pins_MKS_GEN_13.h #define MOSFET_D_PIN 7 pins_RAMPS.h #if DISABLED(HOTEND_USE_E1) #if EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) #if HOTENDS == 1 #define FAN1_PIN MOSFET_D_PIN // Enable 2nd Fan #else #define HEATER_1_PINby Roberts_Clif - Firmware - Marlin
Re: MarlinTarantula-EasyConfig-1.1.x wrong extruder fan - 2 years ago
You can set this in Startup/End G-Code //Fan speed 0 - 255 M106 P0 S128 ; P0 = 1nd Fan M106 P1 S128 ; P1 = 2nd Fanby Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 2 years ago
Have you seen this you-tube video linkby Roberts_Clif - Firmware - Marlin
Re: Babystepping not moving not matter what - 3 years ago
What version of Marlin firmware are you currently working with.by Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 3 years ago
Sorry going off subject for second. My oldest PC is still my favorite home brew with an AMD FX 8150 Processor. This is crazy but while recording video works perfect. With my brand new i5 11600K Processor home brew the audio is offset from video mouth movements, this is unacceptable. Though it work great with all 3D Printer programs / compilers and all other programs, like you said it is a screaby Roberts_Clif - Firmware - Marlin
Re: Babystepping not moving not matter what - 3 years ago
I can not see anything that would stop baby-stepping from working. Personally I use #define BABYSTEP_MULTIPLICATOR_Z 5 // (steps or mm) Steps or millimeter distance for each Z babystep #define BABYSTEP_MULTIPLICATOR_XY 5 // (steps or mm) Steps or millimeter distance for each XY babystep Because of how slowly baby steps changes using my 3D Printer. With my lead screws rise ofby Roberts_Clif - Firmware - Marlin
Re: Babystepping not moving not matter what - 3 years ago
Have you tried to reset the controller using In terminal mode send commands M502 (Factory Default) Then M500 (Save Settings) – Saves the settings to EEPROM.by Roberts_Clif - Firmware - Marlin
Re: Marlin 2.0.9.3 & Build surface alignment - 3 years ago
On my 3D Printer in order to center the nozzle on my bed I added the distance to Z-Safe Homing. My probe is exactly 25 mm directly behind the nozzle in Y direction. This make my Probe center the bed but to get the nozzle to the center added the 25 mm offset to Z safe Home. See code below #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing #define Z_SAFE_HOMING_Y_POINT Y_CENTby Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 3 years ago
Have you got the Marlin 2.0.9.3 I posted to compile yet!. Once you get Marlin 2.0.9.3 to compile we can get started on getting your specific configuration changed as to get your Marlin 2.0.9.3 firmware up an running.by Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 3 years ago
Did not think it needed audio.by Roberts_Clif - Firmware - Marlin
Re: Marlin 2.0.9.3 & Build surface alignment - 3 years ago
Post configuration.h for your Marlin 2.0.9.3by Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 3 years ago
I recorded the compile of this program Video located here Forgot to change the Custom Machine Name #define CUSTOM_MACHINE_NAME "Blu 2.0.9.3" //To whatever you wantby Roberts_Clif - Firmware - Marlin
Re: Firmwear fiasco with ender 3 vs code and SKR 1.4 - 3 years ago
Posted an updated version of Marlin 2.9.0.3 that I created, for this controller. Though do not as of this post have this controller, I will be ordering it when the prices come down. Long story short even though the firmware complies it has never been tested, and may need a few changes to be correct. Attached are Config files.by Roberts_Clif - Firmware - Marlin
Re: connectors for bigtree motherboard - 3 years ago
Too make this a easier task they have Crimping Tool For Dupont XH2.54 JST though the Tool will set you back $20 - $ 30 dollars I do crimp my connectors though on occasion I simply use the 2nd best method XH2.54 JST pig tails. These are precrimped connectors with a short pigtail wires that I solder onto my lead wire with shrink tubing to protect from shorting. You can find them on E-Bay using aby Roberts_Clif - Controllers
Re: Nasa Wrench - 3 years ago
No. Posted On Prusa Printers and they created me a .3mf version of the Nasa wrench which is so much easier to print.by Roberts_Clif - Printing
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
I do not remember posting a link for my New BL touch Slide mount. It has never been finished, when i get some time will again start making measurements adjusting plus it has never tested. And when it is finished there will be two one will attached to rear X-Axis bearing the other will attach to the extruder stepper motor / upper throat cooling heatsink. This is one reason I paused need to desiby Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
I have never gotten PID auto-tune to work in 6 years. If somehow you do make sure you write down what you did an post it for me. The link you requested Wow that took some time, stl file were every where so I had to duplicate all of them and move into a Single folder. Why If I move them would have broken all my previously posted links to them. All the posted STL files are not My Design or remiby Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
I have all the modification STL files on my google drive and there a a few that I recommend. You really need a Proximity sensor have used the the original SN04P an upgraded to a low profile TL_W3MC2 both work the TL_W3MC2 is best of the two. You already have the link for Marlin 2.0.9.3-BL this is setup ready for use with a BL Touch or the 3D Touch. I really do not know a lot about your 3DP08 Frby Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
!! Warning !! I have been having problems using Marlin 2.0.9.3 an Marlin 2.0.8.2 with the Hictop ramps 1.4 compatible controller have reverted to Marlin 2.0.9.2 Problems do not appear in this version can not explain why this version though every function I installed with Marlin 2.0.9.2 work, while some did not on the other versions.by Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
Downloading and flashing firmware is done at your own risk. The Forums have many people that can help including myself though Downloading and flashing firmware is done at your own risk. I have always stated that before you flash firmware make sure you have a copy of your current firmware so you can restore your device to original state. Link to Hictop 3DP 08-12 Marlin 2.0.9.3 newest firmware Heby Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
The firmware I posted was from the Hictop web site you said you could not download without an access code so posted it here for you. If you want an updated version of marlin that works on the Hictop 3DP08, post what version will look in my updated Marlin versions list to see if I updated that version an post. My Updated Versions include 1.1.0 RC8, 1.1.X RC6, 2.0.X alpha, and Marlin 2.0.X up to Mby Roberts_Clif - Firmware - Marlin
Re: Nasa Wrench - 3 years ago
Finally got one to click,I reverted back to Marlin 1.1.9BF however the pin holding the ratchet locking finger (whatever it is called) is frozen top and bottom. This was sliced using Prusaslicer 2.4.0 with 0.3mm nozzle using 0.2 layer thickness with PLA @ 196C. This is still not working as designed and has a very loud click when turning 1/4 shank an harder to turn than the other Nasa wrenches priby Roberts_Clif - Printing
Nasa Wrench - 3 years ago
To whom it may concern: Have 3D Printed many Nasa Wrenches using .4 nozzle with Marlin firmware. Do not know how or when but this ability is now gone. Have Upgraded most Marlin 1.x.x versions and still was able to print the Nase Wrench G-Code from September 16, 2018 and October 25, 2020 both have work successfully sense there creations. Should Note that currently using Marlin 2.0.9.3 firmware aby Roberts_Clif - Printing
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
All my 3D Printers originally looked like the 2nd one 3DP12, now they look like the attached photos. Newest purchased still applying my modifications. You will note that my 1st Purchased 3DP11 3D Printer uses the same firmware as your 3DP08. an I have posted this firmware.by Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
Had to go to work will finish now. My 3DP11 and 3DP12's are upgraded as close as you can get to a 3DP18 . The differences are my 3D Printer all have a 2020 Aluminum frame construction, there are several different controller model numbers and all are compatible. I have a Base v1.3, MPX.3 and a MPK V1 control board all running the same hardware and firmware. If you do not know the home page for Hby Roberts_Clif - Firmware - Marlin
Re: Help with a HICTOP 3dp-18(?) MPK V1 firmware upgrade - 3 years ago
I have 3 Hictop 3D Printers all running Marlin 2.0.9.3 Two 2DP12 and a single 3DP11 I can help you with your current Marlin firmware or Post the configurations for Marlin firmware version that is very close to what you will need. I started with marlin 1.1.0-RC6-Bugfix 4 years ago an have upgraded threw most versions of Marlin not all but most. Start by posting your configuration.h an configuratby Roberts_Clif - Firmware - Marlin
Re: TronXY X5SA Z position wrong after stop / start - 3 years ago
After you adjust your Z offset store the settings they should be available after power off/on. I have upgraded to Marlin 2.0.9.3 and enabled PROBE_OFFSET_WIZARD this make it very easy to set the Z offset. An I have to store Z offset or I will need to re-run PROBE_OFFSET_WIZARD after power off/on. Path:Marlin\Configuration_adv.h Default Value New Value #define PROBE_OFFSET_WIZARD #define PROBE_Oby Roberts_Clif - Firmware - Marlin
Re: Z Endstop homing problem - 3 years ago
Could you post a wiring diagram for your optic-sensor .by Roberts_Clif - Firmware - Marlin
Re: Please help tinkering slicing profile - 3 years ago
Quotethe_digital_dentist Note- when Prusa took on development of their version of Slic3r, they broke the spiral vase mode- it will print but will leave a seam on the print. See: Cura's spiral vase mode works without leaving a seam in the print. Did Not know this Thanks. Does setting seam to random correct this. Although Prusaslicer seems to work, are there any other problems using Prusasliby Roberts_Clif - Slic3r